Squeeze the throttle control all the way up against the hand grip. The engine is governor controlled and must be run at full throttle while tilling. 3. Hold the handle firmly and slowly tilt the unit forward to begin the tilling action. 4. As the tines begin to make contact with the ground, hold back on the handles so that the tines will dig into the soil and not ride forward over the ground. 5. Avoid tilling soil that is too dry as it will pulverize and produce a dust that will not hold water.

Use the list that is for your Overseeder as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware. Tools Required: • Safety glasses • Work gloves • Pencil • Tape Measure • Center punch • Hammer • Electric drill with 21/32" drill bit • Extension cord (if required) • Set of wrenches • 3/8" or 1/2" ratchet wrench set Further Assistance Your dealer wants you to be satisfied with your new seeder. If for any reason you do not understand any part

NO. 1691792 TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE ± 20% SIZE SAE GRADE #2 O SAE GRADE #5 0 SAE GRADE #8 © 8-32 19 In. Lbs. 30 In. Lbs. 41 In. Lbs. 8-36 20 31 43 10-24 27 43 60 10-32 31 49 68 1/4-20 66 8 Ft. Lbs 12 Ft. Lbs. 1/4-28 76 10 14 5/16-18 11 Ft. Lbs 17 25 5/16-24 12 19 25 3/8-16 20 30 45 3/8-24 23 35 50 7/16-14 30 50 70 7/16-20 35 55 80 1/2-13 50 75 110 1/2-20 55 90 120 9/16-12 65 110 150 9/16-18 75 120

Part No. Part Description Comments Revision dwg20618 Drawing Image Number 1. 123-004D KEY 1/4 X 1 2. 300-202S PIN 1 1/8 OD X 7 1/8 USABLE 3. 300-429D CAT III BUSHING 4. 300-431D TUBE RD 2 1/4ODX1 5/32IDX2 5/8 5. 308-360D 12 ROLLER SPACER 1/4 6. 313-006H FRONT ROLLER CLAMP 7. 313-018D FRONT ROLLER HUB 8. 313-168D DRIVE SHAFT PS25120 9. 313-243H PSN2096 FRAME WELDMENT 9. 313-243H82 PSN2096 FRAME WELDMENT ORANGE 10. 313-253H PS2096 FRONT ROLLER WELD 11. 313-254S PS2096 FRONT ROLLER ASSY 12. 313-556

Except for RTA1042, the tillers can be shifted amaximum offset of 7" left or right of the gearbox input shaft by moving the hitch clevises (#1) 7" to the right or left. The RTA1042 is built to be offset 26" to the right when the hitch clevis are set an equal distance away from the gearbox input shaft. The unit can be shifted a maximum of 7" to the left by moving the hitch clevis 7" to the right. For best tillage results, adjust tiller offset to the right by moving the hitch clevis to the left fa

811-789C HH3/8R2 096 9/16FJIC 3/4MORB 01/21/11 PSN2096 Primary Seeders 313-306P 55 Table of Contents Part Number Index Land Pride Section 7: Pull Package PSN 20 SERIES Hydraulic Cylinder 810-001C Applies to PSN2096 56 PSN2096 Primary Seeders 313-306P 01/21/11 Section 7: Pull Package Table of Contents Part Number Index Land Pride PSN 20 SERIES Hydraulic Cylinder 810-001C Applies to PSN2096 Ref. Part No. Part Description Comments Revision dwg21451 Drawing Image Number 810-001C CYL 4X14X1.25 ROD (T

. Section 4 Page 25 Proper tension and alignment on all drive chains. Operator’s Manual Safety decals are correctly located and legible. Replace if damaged. Important Safety Information Sling Bracket Refer to Figure 1-1 The sling brackets allow points at each end to hook the chain for lifting of the unit. When hooking the chain to the sling brackets, be certain to either use a spreader bar on the chain or use a long chain to prevent bending the sling brackets. Sling Bracket Figure 1-1 Tire Track

318-000M h When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! IMPORTANT: Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these instructions for future reference. Your Blade Bolt Kit is exclusively designed for your Land Pride Rotary Cutter. Please read these installation instructions and your Rotary Cutter Operator’s Manua

Install 3/4"-10 x 3 1/2" GR5 hex head cap screw (#5A) with 1 1/4" x 2" spacer (#2) and 3/4" hex flange lock nut (#7). Tighten nut to the correct torque. 6. Install 3/4"-10 x 3 1/2" GR5 hex head cap screw (#5B) and 3/4" hex flange lock nut (#8). Draw nut up snug. 7. Tighten 5/8" hex flange lock nuts (#7) to the correct torque. Section 1: Assembly & Set-up Three point Hitch Assembly Figure 1-1 25773 8 Section 1: Assembly & Set-up Model SBR72 Seed Bed Roller 322-215M 7/06/12 Table of Contents c. At

Your life and the lives of others depend on it! IMPORTANT: Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information. The Baffle Kit and Shredder Kit are exclusively designed for your 20’ Land Pride Rotary Cutter. Please read these installation instructions and your Rotary Cutter Operator’s Manual thoroughly before beginning. Especially read information re