Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Install 3/4"-10 x 3 1/2" GR5 hex head cap screw (#5A) with 1 1/4" x 2" spacer (#2) and 3/4" hex flange lock nut (#7). Tighten nut to the correct torque. 6. Install 3/4"-10 x 3 1/2" GR5 hex head cap screw (#5B) and 3/4" hex flange lock nut (#8). Draw nut up snug. 7. Tighten 5/8" hex flange lock nuts (#7) to the correct torque. Section 1: Assembly & Set-up Three point Hitch Assembly Figure 1-1 25773 8 Section 1: Assembly & Set-up Model SBR72 Seed Bed Roller 322-215M 7/06/12 Table of Contents c. Attach back of tongue with two 3/8"-16 x 1" GR5 cap screws (#8) and 3/8" flange lock nuts (#15). 7. Tighten flange lock nuts (#14, #15 & #16) to the correct torques. 8. Remove wire snap lock pin (#1B). Reorient ball hitch (#6) and clevis hitch (#7) with preferred hitch facing forward and then reattach hitch to tongue (#5) with wire snap lock pins (#1A & 1B). 9. Attach support stand (#3) to wire snap lock pin (#1A). When not in use, rotate stand up and secure in place with second wire snap lock pin (#1B). 10. If clevis hitch (#7) is facing forward, insert 3/4" hitch pin (#12) and secure with hair pin cotter (#13). If ball hitch (#6) is facing forward, store hitch pin and hair pin cotter in a safe location of your choosing. Roller Scraper Assembly Refer to “Torque Values Chart For Common Bolt Size” on page 21 when tightening hardware. Refer to Figure 1-4 on page 9: 1. Attach roller scraper assembly to the Seed Bed Roller frame by inserting 3/8"-16 x 1 1/2" GR5 hex head cap screws (#2) through flat washers (#5A), roller frame, flat washers (#5B), and hex flange lock nuts (#4). 2. Tighten lock nuts to the correct torque. 3. Some adjustment to the scraper teeth can be made by loosening nuts on scraper (#1). Retighten nuts after adjustment has been made. See “Scraper Bar Adjustment” on page 11 for detailed instructions. NOTE: See Figure 1-3. Ball hitch (#6) and clevis hitch (#7) can be installed with either hitch facing forward. Determine which hitch you intend to use and face that hitch forward. Pull Type Hitch Assembly With Drawbar 13" & Higher Figure 1-2 Pull Type Hitch Assembly With Drawbar under 13" High Figure 1-3 25774 26518 Pull Type Hitch Assembly (Optional) Refer to “Torque Values Chart For Common Bolt Size” on page 21 when tightening hardware. Refer to Figure 1-2 & Figure 1-3: 1. Chock front and back of rollers to prevent unit from shifting. Support 2" square tube frame up so that the top of the clevis plates are level. 2. Remove support stand (#3) and wire snap lock pin (#1A) from the clevis plates (shipping location). 3. The front two holes in hitch frame (#4) should be shipped from the factory attached to the front holes in the clevis plates with hitch pins (#17) and linch pins (#11). If not, make this pin connection now. 4. Rotate hitch frame (#4) down to align rear holes in hitch frame with holes at the back of the clevis plates. Insert 5/8"-11 x 1 1/2" GR5 carriage bolts (#10) and secure with 5/8" hex flange lock nuts (#16). Draw nuts up snug, do not tighten. 5. Remove 3/4" hex cap screws (#9), 2" spacer (#2) and and 3/8" cap screws (#8) from hitch frame (#4). 6. Attach tongue (#5) to 3-point hitch (#4) as follows: a. Remove bolts (#8) from back of tongue (#5). b. Attach middle of tongue to hitch (#2) with two 3/4"-10 x 3 1/2" GR5 cap screws (#9), one 2" lg. spacer (#2), and two 3/4" flange lock nuts (#14). IMPORTANT: The tongue (#5) should be as near level as possible when pulling the roller over soil. Before proceeding, determine which hitch assembly below to use that will mount the tongue near level. • Use hitch assembly in Figure 1-2 to mount tongue (#5) if tractor drawbar is lower than 13" • Use hitch assembly in Figure 1-3 to mount tongue (#5) if tractor drawbar is 13" or higher. 9 Section 1: Assembly & Set-up 7/06/12 Model SBR72 Seed Bed Roller 322-215M Table of Contents Roller Scraper Assembly Figure 1-4 3-Point Hook-Up Refer to Figure 1-5 & Figure 1-6: ! DANGER Crushing Hazard between tractor and implement. Do not allow anyone to stand between tractor and implement while backing-up to an implement. Do not operate hydraulic 3-point lift controls while someone is directly behind the tractor or near the Seed Bed Roller. ! DANGER Engage parking brake, shut off tractor and remove key before dismounting from the tractor. ! WARNING See Figure 3-5 on page 15. Chock front and back of roller when using support stand to prevent unit from rolling and causing property damage and/or bodily injury. A 3-Point Category I hitch is required. The lower 3-Point arms of the 3-Point hitch must be stabilized to prevent side-to-side movement. Most tractors have sway blocks or adjustable chains for this purpose. 1. Slowly back tractor up to the Seed Bed Roller while using the tractor’s 3-point hydraulic control to align the lower lift arm hitch holes with the clevis lug holes on the Seed Bed Roller. 2. Engage tractor park brake, shut tractor engine off and remove key before dismounting from tractor. 3. With lower lift arm hi...