Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Your life and the lives of others depend on it! IMPORTANT: Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information. The Baffle Kit and Shredder Kit are exclusively designed for your 20’ Land Pride Rotary Cutter. Please read these installation instructions and your Rotary Cutter Operator’s Manual thoroughly before beginning. Especially read information relating to safety concerns. Also included in the Operator’s Manual is important information on operation, adjustment, troubleshooting, and maintenance for this attachment (some manual sections do not apply to all accessories). A separate Rotary Cutter Parts Manual is available free of charge at or can be purchased from your nearest Land Pride dealer. Have the model and serial numbers of your cutter handy when placing an order. Manual Part Numbers: • Operator’sManual. . . . . . . . . . . . . . . . . 318-474M • PartsManual. . . . . . . . . . . . . . . . . . . . . 318-474P General Information These assembly instructions apply to the Baffle and Shredder Kits listed below: 330-309A SHREDDER/FIXED BLADE/BAFFLE 330-114A BAFFLES, FRONT 330-308A SHREDDER/FIXED BLADE 330-585A BAFFLES, REAR Tools required: • Safety Glasses • Work Gloves • Two3/4"wrenches . . . . . . . . . . . . . . . . .BaffleKitOnly • Two11/2"wrenches . . . . . . . . . . . .ShredderKitOnly • One 55mmwrench . . . . . . . . . . . . . .ShredderKitOnly Further Assistance Your dealer wants you to be satisfied with your new Baffle and Shredder Kits. If for any reason you do not understand any part of this manual or are not satisfied with the service received, the following actions are suggested: 1. Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you. 2. If you are still not satisfied, seek out the owner or general manager of the dealership, explain the problem and request assistance. 3. For further assistance write to: Land Pride Service Department 1525 East North Street P.O. Box 5060 Salina, Ks. 67402-5060 E-mail address lpservicedept@landpride.com Safety Information ! DANGER Always disconnect main driveline from tractor PTO before servicing cutter deck. Cutter can be engaged if tractor is started resulting in cutter damage, bodily injury and/or death. ! WARNING Never work under equipment supported by hydraulics. Hydraulics can drop equipment if controls are actuated or if hydraulic lines burst. Either situation can drop the cutter instantly even when power to the hydraulics is shut off. Assembly Instructions A detailed listing of parts for the Baffle and Shredder Kits is provided on pages 10 & 11. Use the list as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware. IMPORTANT: Read all "Safety Information" above before working on and around the cutter decks. 1. Cutters with Serial No. 536742 and lower: Lower cutter and wings to the lowest position. Cutters with Serial No. 536743 and above: Raise wings fully up and lock into position with transport locks. © Copyright 2010 Printed 3/11/10 Assembly Instructions Bolt Hole Pattern (Left Wing Shown) Figure 1 2 Manual No. 330-148M 3/11/10 Assembly Instructions 2. Place tractor gear selector in park and/or set brakes, shut engine off and remove ignition key. 3. Disconnect main driveline from tractor PTO. Shredder/Fixed Blade/Baffle Kit Kit No. 330-309A This Kit consist of Kits 330-114A and 330-308A. Therefore, see Kit No. 330-114A below for assembly instructions of the front baffles and Kit No. 330-308A on page 4 for assembly instructions of the shredder blades and fixed blades. Front Baffle Kit Kit No. 330-114A A detailed listing of parts for this accessory kit is provided on page 10. Use the list as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware. NOTE: Drilling holes is not necessary on models manufactured after Serial No. 536742. Skip to step 2 below if cutter Serial No. is 536743 or higher. Refer to Figure 1 on page 2: 1. Locate and drill twelve 9/16" dia. holes on each wing deck as shown in Figure 1. If holes already exist, skip to step 2 below. Refer to Figure 2: 2. The wings should be raised and locked into position for the remainder of the assembly. 3. Attach four front baffles (#1) to the left-hand wing deck with 1/2"-13 x 1 1/2" GR5 hex head bolts (#2), 1/2" flat washers (#4) and 1/2" hex whiz nut (#3). 4. Tighten nuts to 76 ft-lbs of torque. 5. Repeat steps 3 & 4 for the right-hand wing deck. Baffle Installation (Left Wing Shown) Figure 2 3/11/10 Manual No. 330-148M 3 4 Manual No. 330-148M 3/11/10 Assembly Instructions Shredder/Fixed Blade Kit Kit No. 330-308A A detailed listing of parts for this accessory kit is provided on page 11. Use the list as a checklist to invento...