to clear/reset this record, press both the uP and DOWN arrow buttons simultaneously (before turning the unit Off) and the display will show 33°f - indicating that record has been cleared - and then turn the unit Off. P/N 1010745 Rev. g 03/06 17 Variety Steamer maIntenance (continued) technical theory of Operation When the Rocker switch (power On/Off) is ON, line voltage flows to the primary side of the step down transformer. the transformer’s secondary side supplies 12 and 24 Vac to the control

this will ensure proper steaming characteristics by creating a thin layer of mineral deposits on the casting. caUtIOn all electrical connections must be in accordance with local electrical codes and any other applicable codes. warnInG electrIcal sHOcK HazarD. faIlUre tO fOllOw tHe InstrUctIOns In tHIs manUal cOUlD resUlt In serIOUs InjUrY Or DeatH. • electrical ground is required on this appliance. • Do not modify the power supply cord plug. If it does not fit the outlet, have a proper outlet in

Acorn Nuts Weld Screws Figure 9. Replacing Spring Tensioner Assy. 4. Make sure the spacers are placed inside the tensioner arm. The spacers are smaller than the holes to allow the tensioner to pivot freely. Replacing Conveyor Motor and Fan Blade NOTE: A small amount of Loctite (Blue & Red) is required for proper gear motor installation. 1. Remove control cover. 2. Disconnect the motor wires and remove the drive motor and drive motor bracket (Figure 10). Discard the 8-32 x 5/16” mounting bracket

If low or zero voltage, replace power cord. If voltage is correct, check for correct voltage out of rocker switch. If low or no voltage, replace rocker switch. Wiring problem. Check all electrical connections for burns, discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the same (or higher) rated wire. Platen inoperative. To check platen: Use an Ohm meter to test resistance of the platen heater (disconnect 1 wire to isolate heat

To reset this thermostat, allow sufficient time (10-15 minutes) for the unit to cool down, then fully depress the reset button located at the rear of the unit (Figure 5). If the unit requires continuous resetting, contact your Roundup authorized service agency. CONVEYOR INTERLOCK SWITCH A conveyor interlock switch is located on top of the unit under the heat shield (Figure 4). The conveyors will not rotate unless the heat shield is in place and interlock switch is activated (depressed). Bun Thic

Nickel. MAINTENANCE (continued) Replacing the Optional Roller Tensioners 1. Remove the acorn nuts and old roller Tensioner Assembly (Figure 12). 2. Replace Tensioner Assembly, and reassemble. 3. Make sure the spacers are placed inside the Tensioner arm. The spacers are smaller than the holes to allow the Tensioner to pivot freely. Weld Screws Acorn Nuts Tensioner Assy. Spacers Teflon Tape Figure 12. Replacing Roller Tensioner Assy. Figure 14. Measuring Roller Tensioner Replacing the Spring Tensi

D 04/06 2 TABLE OF CONTENTS Owner Information .....................................................2 General ......................................................................2 Warranty Information .................................................2 Service/Technical Assistance ....................................2 Important Safety Information ....................................3 Specifications .............................................................4 Electrical Ratings ................

Simple push-button action delivers a shot of water which is immediately converted into steam. Because the amount of steam is consistent, it removes the guesswork and produces a uniform finished product from one operator to the next. This manual provides the safety, installation and operating procedures for the Deluxe Food Warmer (steamer). We recommend that all information contained in this manual be read prior to installing and operating the unit. Your Deluxe Food Warmer (steamer) is manufactur

PRESS ‘ENTER’ TO CONTINUE message. Press Enter or wait and the system will prompt you for the password again. 5. The system displays the TURN OFF POWER, WAIT 10 SEC, RESTORE POWER message. Unplug the power cord and wait for ten (10) seconds or more, and then plug the cord in again. 6. The system then cycles through initialization displays and prompts you to set the Date and Time. Follow the instructions in the Set Date/Time Modes section of this manual. The system can then be re-programmed as de

NOTE: Do not use a dripping wet cloth. Wring out before use. 6. MS-150/250 Models: Assemble the handle, handle guard and mounting bolt to the spatula as shown in Figure 1. 7. Re-install all removed parts. Equipment Setup GENERAL When placing the unit into service, pay attention to the following guidelines: • Make sure power to the unit is off and the unit is at room temperature. • Do not block or cover any openings on the unit. • Do not immerse cord or plug in water. • Keep cord away from heated