Оценок - 3, средний балл: 4.3 ( )

Производитель: Land Pride Размер: 586.06 kb Название файла: 9b7bd49f-932c-43b0-ab99-7781759d1139.pdf Язык инструкции:

NO. 1691792 TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE ± 20% SIZE SAE GRADE #2 O SAE GRADE #5 0 SAE GRADE #8 © 8-32 19 In. Lbs. 30 In. Lbs. 41 In. Lbs. 8-36 20 31 43 10-24 27 43 60 10-32 31 49 68 1/4-20 66 8 Ft. Lbs 12 Ft. Lbs. 1/4-28 76 10 14 5/16-18 11 Ft. Lbs 17 25 5/16-24 12 19 25 3/8-16 20 30 45 3/8-24 23 35 50 7/16-14 30 50 70 7/16-20 35 55 80 1/2-13 50 75 110 1/2-20 55 90 120 9/16-12 65 110 150 9/16-18 75 120 170 5/8-11 90 150 220 5/8-18 100 180 240 3/4-10 160 260 386 3/4-16 180 300 420 7/8-9 140 - 400 600 7/8-14 155 440 660 1-8 220 580 900 1-12 240 640 1,000 NOTE: 1. These torque values are to be used for all Simplicity hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. For prevailing torque locknuts - use 65% of grade 5 torques. b. For flange whizlock nuts (and screws) - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings all torque values must meet this specification. BOLT HEAD MARKING S.A.E. GRADE: * o 5 8 ^ Table of Contents TORQUE SPECIFICATIONS ............................................ Inside Front Cover RECOMMENDED ACCESSORIES ....................................................... 1 SAFETY DECALS....................................................................... 1 SAFETY RULES ........................................................................ 2 ASSEMBLY ............................................................................ 3 OPERATION AND STORAGE ........................................................... 5 TROUBLESHOOTING .................................................................. 6 STANDARD FASTENERS ............................................... Inside Back Cover Recommended Accessories On slopes over 15% (8.5°), use two front wheel weights (1690555). Always mow up and down the face of slopes, never across the face. Never mow on slopes greater than 30% (16.7°). Safety Decals ° A WARNING ° O' 00 NOT OPEN COVER WITH ENGINE RUNNING 00 NOT OPERATE ENGINE WITHOUT w\ COMPLETE CATCHER IN PLACE WHEN OPERATING ON SLOPES ' / 1 REFER TO OPERATOR'S MANUAL FOR COUNTERWEIGHTS L^\ - L~J: J J / A DANGER ROTATING CUTTING BLADE DO NOT OPERATE MOWER WITHOUT DEFLECTOR OR ENTIRE GRASS CATCHER IN PLACE. 1 Safety Rules A Read these safety rules and the safety rules in your rider Operator’s Manual and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal Injury to yourself, or damage to property or equipment. The triangle ^ in the text signifies important cautions or warnings which must be followed. 1. Know the controls and how to stop the rider quickly. READ THE TRACTOR’S OPERATOR’S MANUAL. 2. Shut the engine (motor) off before attaching, adjusting or disconnecting the collection system, 3. Check the grass catcher frame to make sure it is attached securely to rider. 4. Look behind to make sure the area is clear before backing up. 5. CAUTION: For added rider stability and to prevent tipping or loss of control; a. DO drive in reduced speed on uneven ground and when turning corners. b. Reduce loads on hillsides. It is recommended that the Collection System be kept only half full when negotiating any slopes. Start mowing on slopes when the Collection System is empty. c. Mow up and down the face of slopes: never across the face of any slope. 6. CAUTION: Objects may be thrown from mower. For your safety. a. DO NOT open the cover while the mower blades are turning. Shut off the engine before removing the grass chute. b. Be sure the complete Collection System is in place (cover secure and grass chute connected) before operating the mower. c. DO check the cover and bags frequently for wear and tear. Replace with the new cover for safety protection. 7. For best results when mowing grass: Set the mowertocut offfrom 1 to2inches of grass (leave 1-1/2" of grass). If grass is exceptionally tall, set your mower as high as possible for first cutting. Lower cutting height at succeeding cuttings until proper height is reached. It may be necessary to mow tall grass at a slower rider ground speed (keep engine at full throttle). Xk. WARNING Do not operate the rider unless the entire grass catcher system or mower discharge deflector is properly Installed. ^ WARNING Before raising cover, disengage mower, turn off engine and remove the key. Do not remove catcher tube from adapter or cover while mower is running. 2 Assembly ATTENTION SETUP PERSONNEL: As setup personnel you have the obligations to know the product better than the customer. This includes safety related items. Prior to setup, thoroughly familiarize yourself with the Operator’s Manual. Pay special attention to all safety warnings. Remember, it is your responsibility to set...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: