Assemble the feed door handle and the ash door handle as shown in Figure 8. Install the latches as shown in Figure 9. 1. 2. 3. FIG. 8 FIG. 9 BLOWER & COMPONENT ASSEMBLY - FIG. 10 BLOWER & COMPONENT ASSEMBLY - FIG. 10 1. Attach the Honeywell Limit Control to the bracket as shown below, using (2) of the #12 x 3/4" Tek Screws provided in the parts bag. 2. Attach the 2x4 Junction Box to the bracket. Use (2) of the #12 x 3/4" Tek Screws provided. Also, attach the flexible conduit from the Limit Contr
Control knob not in PILOT position. Control knob not pressed in while in Pilot position Air in gas lines when installed. ODS/Pilot is clogged. Replace control valve. Turn on gas supply or open manual shutoff valve. Turn control knob while in PILOT position. Press in control knob while in PILOT position. Continue holding down control knob. Repeat igniting operation until air is removed Replace ODS/pilot assembly or get is serviced ODS/Pilot lights, but flame goes out when control knob is released
12) to the pilot position and hold down. Light match and place near pilot. Once pilot is lit, continue to hold the knob for about ten seconds. Then follow steps 7 thru 10 on page 12. CHECKING FLAME APPEARANCE Flames from the pilot, front and rear burner should be visually checked when the heater is installed. In addition a periodic visual check of the flames should be made. PILOT FLAME The pilot flame should always be present when the If the pilot flame does not touch the thermocouple, then heat
2 HOW THIS HEATER OPERATES ..................................................................................................................................................................... 2 SELECTING A LOCATION FOR THE HEATER ................................................................................................................................................ 2 FLOOR PROTECTION .........................................................................................................
Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fibers. PROPER INSTALLATION SEQUENCE: 1. Install the rear log (#2) on the rear set of locators. Visually check to verify the log is securely placed on the locators. 2. Install the front log (#1) on the front locators. Visually check to verify the log is securely placed on the locators. 3. Install
The National Fuel Gas Code defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 BTU per hour (4.8m3per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space is defined as a space whose volume is not less than 50 cubic feet per 1,000 BTU per hour (4.8m3per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed, throu
The installation comply with their rulings. Observe closely the clearances to combustibles (page 4). 2. Do not install this heater in a mobile home or trailer. 3. Always connect this heater to a chimney and vent to the outside. Never vent to another room or inside a building. 4. Do not connect a wood burning heater to a Type B gas vent. This is not safe and is prohibited by the National Fire Protection Association Code. This heater requires approved masonry or UL/ ULC Listed Residential Type and
Logwood C226 Logwood C226Logwood C226Logwood C226Logwood C226Logwood C226 TESTED TO TESTED TOTESTED TOTESTED TOTESTED TOTESTED TOUL 1482 UL 1482UL 1482UL 1482UL 1482UL 1482& &&&&& CAN/ULC S627 CAN/ULC S627CAN/ULC S627CAN/ULC S627CAN/ULC S627CAN/ULC S627 CAUTION! CAUTION!CAUTION!CAUTION!CAUTION!CAUTION! Read All Instructions Care- Read All Instructions Care-Read All Instructions Care-Read All Instructions Care-Read All Instructions Care-Read All Instructions Care- fully Before Starting The In- fu
Box 151 • South Pittsburg, TN 37380 • (423) 837-2100 VENT-FREE PEDESTAL GAS HEATER INSTALLATION AND OPERATION INSTRUCTIONS This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to "Adequate Combustion And Ventilation Air" on page(s) 6 of this manual. WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, p