... . . ....... . . . . ©Copyright 2005 ATLAS COPCO CONSTRUCTION TOOLS AB 2005-06 NACKA • SWEDEN No 3392 5042 01 1 English ! . INTRODUCTION ....................................................................................................................... 2 SAFETY INSTRUCTIONS ........................................................................................................ 2 Introduction to safety ...........................................................................

The Atlas Copco LS 14 Cut-off Saw and the LS 16 Cut-off Saw are delivered with 2 m 3/8” tail-hoses with .” Flat-Face quick-release couplings. The direct driven hydraulically powered design provides consistent speed and torque. It also enables underwater cutting. 5 English For precise and clean cutting jobs on roads, sidewalks and floors, the Atlas Copco LSC Cart for the Cut-off Saw is recommended. The use of the Cart gives a better working posture, and the cutting depth can be adjusted by means

• Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time: Works: Day Night Test 5 Sec x x Auto 1, 5, 10 min. x Manual Until Dawn* x * resets to Auto Mode at dawn. Note: When first turned on wai

Junction Box Lamp Holders . Turn power off at the fuse or circuit breaker. . Remove the existing light fixture, if present. 598-1096-01 -2 TEST AND ADJUSTMENT . Turn on the circuit breaker and light switch. NOTE: Sensor has a 1 1/2 minute calibration period before it will detect motion. When first turned on, wait 1 1/2 minutes. . Turn the RANGE control to the mid position and the ON-TIME control to the TEST position. ON-TIME RANGE 10 5 1 TEST MIN MAX Bottom of Sensor Avoid aiming the control at:

• Automatically turns lighting off. • Dual Light Level • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Sensor Lamp Holders (3 sizes included) 2 Shells Light Control 6 Screws Cover Plate 2 Wire Connectors Mounting Bolt Gasket Mounting Strap Rubber Plug Plastic Hanger Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes req

. Walk through the coverage Ball area noting where you are Joint when the lights turn on. Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (2.5 cm) away from the lamps. . Adjust the RANGE as needed. RANGE set too high may increase false triggering. . Secure the sensor head by tightening the clamp screw. Do not overtighten the screw. . Set the amount of ON-TIME you want the lights to stay on Aim Sensor Down for Short Coverage Aim Sensor Higher fo

(1 m). Sensor Least Sensitive . Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. . Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times whenmotionisdetected).Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (25 mm) away from the bulbs. Most Sensitive Clamp Screw Ball Joint Aim Sensor Down for Short Coverage 4 598-1098-02 SPECIFICATIONS Range ............

(1 m). Sensor Least Sensitive . Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. . Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times whenmotionisdetected).Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (25 mm) away from the bulbs. Most Sensitive Clamp Screw Ball Joint Aim Sensor Down for Short Coverage 4 598-1098-02 SPECIFICATIONS Range ............

2. The light control may be picking up a heat source like an air vent, dryer vent, or brightly painted, heat- reflective surface. 3. Light control is in manual mode. 1. Heat or light from the flood lamps may be turning the light control on and off. 2. Heat being reflected from other objects may be turning the light control on and off. 3. Light control is in the TEST mode and warming up. 4. Light may be leaking through the flood lamp reflectors. Light control is detecting its own lights. 1. Turn

Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE. Manual mode works only with the ON-TIME switch in the 1, 5, or 10 position. 240-026-A © 2008 Atlas Lighting Products, Inc. 598-1092-02 Mode Switching Summary TEST Move ON-TIME Switch to 1, 5, or 10 minutes AUTO Flip light switch off for one second then back on* MANUAL MODE * If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control