Be sure the lights are cool before cleaning the hood – they are halogen and become extremely hot. Cleaning the Filter The aluminium mesh filters should be washed by hand or in the dishwasher as required. Damaged and worn filters must be replaced immediately. (Do not operate blower when filters have been removed). Allow filters to dry before replacing them, otherwise water will be drawn into the blower. If a carbon filter has been fitted, this must be replaced every 6 months as a minimum, dependi

Calculate your duct run by measuring linear feet and adding the elbows, transitions and caps based on the table alongside. Maximum Run 6” or 3 1/4 x 10” duct 100 FT Deduct Each 90 elbow used 15FT Each 45 elbow used 9FT Each 6” or 3 1/4 x 10” duct Transition used 1FT Each 3’1/4 x 10” to 6” Transition used 5FT Side Wall with damper 30FT Roof Cap 30FT The ducting connection to the hood must be in line with the central vertical axis of the range hood 1” away from the back wall on which the hood is t

The ducting connection to the hood must be in line with the central vertical axis of the range hood 1” away from the back wall on which the hood is to be mounted. Range hoods may interrupt the proper flow of combustion gases from fireplaces, gas furnaces and gas water heaters. To minimize the risk of drawing these lethal gases back into the home, please follow the heating equipment manufacturers safety standards and guidelines carefully. Refer to NFPA and ASHRAE for additional information. E L E

Please read all the instructions in this manual before installing the appliance. Save these instructions for future reference. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure they do not play with the appliance. If the range hood is vented, the air so vented must be ducted into a dedicated duct that is not showed with any other equipment whatsoever. All ducting must conform to all requirements of the loc

Draw a horizontal line fractionally above where the bottom of the range hood will be positioned. This is the underside of the range hood. Marking the Fixing Holes for the Range Hood Find the marking template provided called the “Assembly Scheme”. Place the template against the wall. Align the horizontal line on the wall with the horizontal line on the template (indicated by two heavy arrows). Now align the vertical line on the wall with the “Central Axis” line on the template. Figure 3 Gently ta

Position the upper chimney so that it can be fixed via the holes on the side of the ‘Y” bracket on the ceiling (refer to Figure 11). Connecting the Screen (SU 202 Only) Before attaching the screen the power unit wipe the face of the flange to ensure there is no Figure 11 5 Figure 12 Figure 13 grit present – if there is this will most definitely crack the glass. The plastic washers must be positioned between the screw head and the glass. Fit the screen – please have someone hold this in place whi

When frying, oil in the pan can easily overheat and ignite. Heat oil slowly in an appropriately sized pot (covering the entire burner) to reduce the risk of boiling over and burning In the event of a range top grease fire, observe the following: Switch OFF the range hood. Turn off the cook top then smother flames with a close fitting lid, cookie sheet or other metal tray. If the flames do not go out immediately. EVACUATE AND CALL THE FIRE DEPARTMENT. Never pick up a flaming pan – you may be burn

Follow the instructions for cleaning filters in this booklet. Once the grease filters have been cleaned and replaced, reset by pressing the timer button (F). Do not rely solely on this indicator. Generally, the grease filter should be washed on a regular basis to avoid grease filter fires. The blower should be turned on for approximately 5 minutes before cooking in order to establish air currents upward through the hood. Use the low speeds for normal use and the higher speeds for strong odors an

Attach bracket “A” to the ceiling permanently. If re-circulating, attach the deflector to Bracket “A” before fixing it to the ceiling – refer schematic on page 5. Fix Bracket “C” to the power unit with the nuts and washers supplied (Items “A” on the schematic on page 5). Please ensure that the bracket is installed as shown to enable full access to the square plastic black box and the metal electrical junction box. Slide Bracket “B” over Bracket “C” (once again ensure full access to the plastic a

Ensure the entire structure is sturdy -serious injury, death and MAJOR damage could result should the unit not be well connected to the frame structure within the ceiling. This is of utmost importance – do not go any further until this has been tested and double checked – the installer has sole responsibility for the safe installation of this product. Connecting Electricity and Ducting Make sure power is turned off at the source. Make the electrical connection (see figure 1). Test the functionin