Each time a button is pressed, the incline will change by 0.5%. Note: After a button is pressed, it may take a moment for the treadmill to reach the selected incline setting. Follow your progress with the display. When the manual mode is selected, a track representing 1/4 mile will appear in the upper right corner of the display. As you walk or run on the treadmill, the indicators around the track will appear in succession until the entire track appears. The track will then disappear and the ind

Climber RESISTANCE Changes the height of the column and affects the Custom Program step resistance. 4. When you have set the column height, press the down arrow key on the navigational keypad to move to the next column. You can press the up arrow key to return to previous columns. 5. Continue adjusting the profile for each column. Note: Two custom programs are available on the treadmill. Some Precor products contain only one custom program. The prompt indicates which one you have accessed. To se

45 The Optional Power Adapter Kit .................................................... 45 Replacing the Battery ........................................................................ 46 Commercial Cardiovascular Equipment Limited Warranty ..... 47 Chapter 1 Assembling the AMT Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that is, on the opposite side of the control console from a person using

Each kit comes complete with all the hardware required to install a handrail on one side of the treadmill. If you wish handrails on both sides of the treadmill, you must order two (2) option kits. When you receive the Handrail Option kit, check its contents with the list below: Note: If you purchase both handrails, check the contents of both kits with the list below: Handrail Option Kit Contents One handrail One upper end clamp One upper center clamp Three large bolts (two 5/16 - 18 x 2.5 and on

Important: If you are installing both handrail options, install a handrail on one side before proceeding to the other side of the treadmill. Attach the front portion of the handrail first. This helps you determine where to position the lower handrail clamp. Electronic console Bolt End clamp Center clamp Handrail end cover Upper frame Finger guard Rear roller Bolt Attaching the front section of the handrail. Diagram 2 Upright support Handrail Guide rail Side rail Nut plate C O M M E R C I A L P R

Table of Contents Important Safety Information 3 Before You Start 4 Assembly 5-9 Moving Instructions 10 Power Requirements 11 Console Panel Functions 12 Program Operation 13-14 Program Profiles 15 Monitoring Your Heart Rate 16-17 Warm Up Exercises 18 Changing to MPH or KM 19 Calibration Sequence 20 Belt Adjustment 21 Maintenance Instructions 22 Error Messages 23 Troubleshooting 24 Parts List 25-26 Exploded View 27-28 Warranty Information 29 2 Important Safety Information WARNING! Before using th

The incline must be at the lowest setting when the treadmill is folded to the storage position or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key is removed, the console is in the “demo” mode. See page 18 and turn off the demo mode. When you are finished using the treadmill, move the on/off switch near the power cord to the off position and unplug the power cord

IMTL99000 Serial No. Write the serial number in the space above for future reference. QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. The trained technicians on our Customer Hot Line will provide immediate assistance, free of charge t

When you are finished exercising, remove the key from the console. See step 7 on page 15. 4 16 HOW TO USE A CUSTOM PROGRAM 1 Insert the key into the console. See HOW TO TURN ON THE POWER on page 12. 2 Select a custom program. To select a custom program, press the Custom Programs button repeatedly until “P-15” or “P-16” appears in the right display. When a custom program is selected, the left display will flash the maximum incline setting of the program for a few seconds, and the right display wi

1. Make sure that the power cord is unplugged. Remove the indicated Screw (40) and the Access Door (76). 2. Remove the paper from the adhesive pad on the back of the receiver (A). Orient the receiver so the small cylinder is near the lower edge of the receiver and is facing the Console Back (51) as shown. Firmly press the receiver onto the indicated corner of the Access Door (76). Connect the wire on the receiver to the Pulse Wire (101) extending from the Console Back. 3. Make sure that no wires