selling policies. The sole source governing the rights and remedies of any purchaser of this equipment is the relevant Eaton Electrical Inc. selling policy. NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OR WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE, ARE MADE REGARDING THE INFORMATION, RECOMMENDATIONS AND DESCRIPTIONS CONTAINED HEREIN. In no event will Eaton Electrical Inc. be responsible to the purchaser or user i

NOTE NOTE c. Slide the yoke from side to side to loosen the yoke bearing races (54) within the housing. The races are a normal slip fit but may be tight. Use an open end wrench between the yoke and the pintle bearing to help slide out the races. Apply pressure to bearing (55) at the approximate center and allow the bearing rollers to gently press the race out of the housing. 15. Remove yoke (56) and drive shaft (48) from the housing together. Turn the yoke at an angle and slide the two parts out

To prevent this condition from continuing, the small orifice meters the fluid trapped in the load back through the flat cut-off compensator spool to case drain. The actuator load pressure will decrease gradually causing the load sensing spool to open pressure to the yoke stroking piston, bypassing the flat cut-off compensator. As the actuator load pressure reduces, the pump outlet pressure will reduce until minimum pump pressure is obtained. When the minimum flow/minimum pressure condition occur

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 A.Purpose of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 B.General Information (Related Publications/Model Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A worksheet of information that will be needed to complete this startup is found on Page 6 of this guide. Make sure you have all the listed information available before starting, either by filling in the worksheet, or from job documents. Several conventions are used in this document. COURIER text indicates screen output or screen menu items. BOLD COURIER indicates user button presses. Navigation through the LCD programming tool menus is via the four buttons to the right of the screen as shown ab

1.2 General safety instructions 1. Before carrying out any installation or maintenance work, make sure that the power supply of the digital display is switched off. 2. Only use this digital display in a way according to its intended purpose: If its technical condition is perfect. Adhering to the operating instructions and the general safety instructions. 3. Adhere to country or user specific regulations. 4. The digital display is not intended for use in areas with risks of explosion and in the b

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Receiving, Handling, and Storage . . . . . . . . . . . . . . . . . . . . 10 Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation and Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Drawout and Fixed Switching Devices . . . . . . . . . . . . . . . . 22 Operation of the Bypass Isolation Tr

Painting the Speaker Speaker Grill: Remove the speaker grill from the speaker frame. Paint the grill lightly, being careful not to clog the holes. Do not paint the grill while it is still on the speaker. Speaker Frame: Eaton suggests painting all parts of the speaker prior to the installation. If you must paint after installation, place the provided paint guards around the grill area. After the paint guards are in place, paint the frame of the speakers. Adjusting the Tweeter EATON CORPORATION Cu

Insert the speaker into the hole. Turn All Mounting Brackets into the “in” Position Mounting Brackets in the “in” Position EATON CORPORATION Cutler-Hammer Wall and Ceiling Mounted Speakers Installation Manual IM00412012E Effective: May 2006 Speaker Installation (continued) Reapplying the Speaker Grill Make sure that the speaker is level and carefully tighten the mount-Once the tweeters are adjusted, the grill can be replaced. Recheck ing screws to secure the speaker. As you tighten the screws, t

Caution: Make sure to observe polarity (positive + to positive + and negative – to negative -). Finally, to mount the speaker, turn all the mounting brackets in toward the speaker. This will allow the speaker to easily fit into the hole you have just cut. Insert the speaker into the hole. Turn All Mounting Brackets into the “in” Position Mounting Brackets in the “in” Position EATON CORPORATION Cutler-Hammer Wall and Ceiling Mounted Speakers Installation Manual IM00412012E Effective: May 2006 Spe