Войти:
Скачали: 15   Размер: 19 kb   Производитель: Delta  
Категория: Станки
@name

Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment should comply with ANSI S3.19 standards, and dust mask protection should comply with MSHA/NIOSH certified respirator standards. 7. DO NOT WEAR TIE, GLOVES, or loose clothing. REMOVE WATCH, RINGS, and other jewelry. ROLL UP SLEEVES. 8. USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, secured, and working correctly. 9. ROUGH CUT THE WORKPIECE as close as possible to the finished shape befor

Скачали: 12   Размер: 1 mb   Производитель: RIDGID  
Категория: Станки
@name

. . WARNING: To reduce the risk of injury, the user must read and SAVE THIS MANUAL FOR understand the operator’s manual FUTURE REFERENCE before using this product. Part No. SP6489 Printed in China Table of Contents Section Page Table of Contents ................................2 Safety Instructions For Wood Turning Lathe .................................................2 Safety Symbols ...................................3 Before Using the Lathe .......................3 When Installing Or Movin

Скачали: 21   Размер: 2 mb   Производитель: Woodstock  
Категория: Станки
@name

• Lighting: Lighting should be bright enough to eliminate shadow and prevent eye strain. • Electrical: Electrical circuits must be dedicated or large enough to handle amperage requirements. Outlets must be located near each machine, so power or extension cords are clear of high-traffic areas. Follow local electrical codes for proper installation of new lighting, outlets, or circuits. MAKE your shop “child safe.” Ensure that your workplace is inaccessible to youngsters by closing and locking all

Скачали: 2   Размер: 2 mb   Производитель: Grizzly  
Категория: Станки
@name

Not To Scale Part ID.: HAE0216 Ref No.: Part No.: Material Blank Description: Finished Part Description: 9 PH8103009 Aluminum Aluminum Plate Blank 130 x 123 x 14mm Mounting Plate Qty To Make 1 Note: All dimensions are in millimeters. Not To Scale Part ID.: HAE0309 -15 h8103 stirling Engine Kit 3 Ref No.: Part No.: Material Blank Description: Finished Part Description: 10 PH8103010 Brass Brass Rod Blank 12 x 175mm Threaded Support Staff Qty To Make 4 Note: All dimensions are in millimeters. Not T

Скачали: 8   Размер: 2 mb   Производитель: Woodstock  
Категория: Станки
@name

Bolting to Concrete Floors Lag shield anchors with lag bolts and anchor studs (Figure 5) are two popular methods for anchoring an object to a concrete floor. We suggest you research the many options and methods for mounting your machine and choose the best that fits your specific application. NOTICE Anchor studs are stronger and more permanent alter- natives to lag shield anchors; however, they will stick out of the floor, which may cause a tripping hazard if you decide to move your machine at a

Скачали: 3   Размер: 74 kb   Производитель: Woodstock  
Категория: Станки

Скачали: 3   Размер: 1 mb   Производитель: Woodstock  
Категория: Станки
@name

REVISED AUGUST, 2008 (TR) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT #5378TR THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China Ak WARNING! This manual provides critical safety instructions on the proper setup, operation, maintenance and service ofthis machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The

Скачали: 5   Размер: 4 mb   Производитель: Woodstock  
Категория: Станки
@name

This belt is 27.5" long. The high range belt is always used on pulleys A and C without using the tensioner. This belt is 33" long. 4. Close the side cover and secure it shut with the cap screw. The lathe is now ready to use at 150 RPM. ▲WARNING Use a low RPM when machining heavy eccentric workpieces; Objects thrown from a lathe can cause serious injury or death. ▲WARNING Use a minimum of three independent clamping devices when turning eccentric workpieces on the faceplate. Failure to provid

Скачали: 13   Размер: 686 kb   Производитель: Southbend  
Категория: Станки
@name

• Secure Clamping: A thrown workpiece may cause severe injury or even death. When swapping the chuck jaw positions, use a torque wrench to re-torque the M8-1.25 jaw mounting cap screws to 29 ft/lbs. When clamping a workpiece, maximum gripping force is attained at full jaw and scroll gear engagement. If the jaw and scroll gear are partially engaged, clamping force is reduced. • Chuck Speed Rating: Exceeding the maximum rated speed indicated on the chuck, or using excessive spindle speeds with an

Скачали: 9   Размер: 715 kb   Производитель: Southbend  
Категория: Станки
@name

Ignoring this warning can lead to a severe crushing injury or finger amputation! Figure 1. Features. Manufactured with high-tech German CNC machinery. Grease fitting for complete internal lubrication. Universal plain-back mounting. Hardened steel jaws for durability and extreme clamping force and grip. Two-piece jaws for speedy internal/external clamping changes. Designed for up to 2000 RPM. Specifications • OD Clamping Range...0.32"-6.30" (8-160mm) • ID Clamping Range ..2.17"-5.90" (55-150mm) •





Категории