Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
. Section 4 Page 25 Proper tension and alignment on all drive chains. Operator’s Manual Safety decals are correctly located and legible. Replace if damaged. Important Safety Information Sling Bracket Refer to Figure 1-1 The sling brackets allow points at each end to hook the chain for lifting of the unit. When hooking the chain to the sling brackets, be certain to either use a spreader bar on the chain or use a long chain to prevent bending the sling brackets. Sling Bracket Figure 1-1 Tire Track Remover Assembly For shipping purposes the Tire Track Removers are assembled 180 degrees from their operating position. Refer to Figure 1-2 1. Remove Track Remover (#1). 2. Flip Track Remover over 180 degrees and reassemble as shown with 1/2” u-bolt (#4), lockwasher (#3) and nut (#2). Tire Track Remover Figure 1-2 20589 9 Section 2: Assembly & Set-Up (Optional) 6/15/10 PS2096 Series Primary Seeders 313-308M Table of Contents Small Seeds Box (S/N 397503+) Small Seeder Box assembly 1. Remove the eight bolts, lock washers and nuts that are assembled in the front of the main box. Retain two bolts, lock washers and nuts and use these to plug the two holes in the front of the Small Seeds Box. Refer to Figure 1-6: 2. Assemble the Small Seeds Box (#1) at the ends with the four 5/16” bolts (#3), flat washers (#7), lock washers (#6) and nuts (#5). Do not tighten until spacers (step 3) are installed. 3. Align the four box spacers (#2) to the inner holes of the Small Seeds Box and the main box and assemble the four longer 5/16” bolts (#4), flat washers (#7), lock washers (#6) and nuts (#5). 4. Refer to Figure 1-4. Attach rubber seed tubes to feeder cups with clamps provided and then into the small holes in seed drop without clamps. Push rubber hoses into the seed drop hole to remove any excess slack. Small Seeds Box Assembly Figure 1-3 20587 Rubber seed hoses clamped to feeder cups 20596 Plug 2 Holes Insert rubber hoses into seed drop holes Small Seeds Tube Assembly Figure 1-4 Section 2: Assembly & Set-Up (Optional) 10 Section 2: Assembly & Set-Up (Optional) PS2096 Series Primary Seeders 313-308M 6/15/10 Table of Contents Small Seeds Drive Assembly Refer to Figure 1-8: 1. Place decal “Danger Guard Missing” (#18), “Danger Moving Parts” (#19) and “Seed Rate Chart” (#20) in locations shown. 2. Assemble chain guard mounts (#5) with the 1/4” flange bolts (#8) and flange nuts (#11). Do not tighten until the complete drive has been assembled and the chain guard (#16) installs properly. The chain guard mounts are slotted for easier chain guard mounting. 3. Install chain idler with welded on spacer (#2) and chain idler (#3) with 1/2” nut (#9). 4. Assemble the spacer (#4) and speed change sprocket assembly (#7) to the 5/8” welded on bolt with the 5/8” lock washer (#12) and nut (#10). 5. Assemble the front roller sprocket (#13) and key (#1) to the front roller shaft. 6. Install chain (#14) first and then chain (#15). Tighten chains with idlers (#2) and (#3). 7. Assemble chain guard (#16). Position chain guard mounts (#5) where needed and tighten hardware. 20588 Small Seeds Drive Assembly Figure 1-5 11 Section 2: Assembly & Set-Up (Optional) 6/15/10 PS2096 Series Primary Seeders 313-308M Table of Contents Small Seeds Box (S/N 397502-) Small Seeds Box Assembly 1. Remove the eight bolts, lockwashers and nuts that are assembled in the back of the main box. Retain two bolts, lockwashers and nuts and use these to plug the two holes in the back of the main box where the SMV sign will be removed. Refer to Figure 1-6: 1. Remove the SMV (#11) and SMV mounting bracket from the main box. 2. Assemble the Small Seeds Box (#1) at the ends with the four 5/16” bolts (#4), flatwashers (#10), lockwashers (#9) and nuts (#6). 3. Align the four box spacers (#2) to the inner holes of the small seeds box and the main box and assemble the four longer 5/16” bolts (#5), flatwashers (#10), lockwashers (#9) and nuts (#6). 4. Install SMV (#11) with SMV mounting bracket to Standard Seed Box Assembly (#1). Refer to Figure 1-7 5. Attach the rubber seed tubes to the seed cups and then through the small seed holes below. 20596 Remove SMV and plug the 2 Holes Small Seeds Box Assembly 20607 Figure 1-6 20606 Attach hose to seed cups and through holes below Small Seeds Tube Assembly Figure 1-7 12 Section 2: Assembly & Set-Up (Optional) PS2096 Series Primary Seeders 313-308M 6/15/10 Table of Contents Small Seeds Drive Assembly Refer to Figure 1-8: 1. Place decal “Danger Guard Missing” (#17), “Danger Moving Parts” (#18) and “Seed Rate Chart” (#19) in locations shown (beneath lid). 2. Assemble chain guard mounts (#5) with the 1/4” flange bolts (#7) and flange nuts (#10). Do not tighten until the complete drive has been assembled and the chain guard (#15) installs properly. The chain guard mounts are slotted for easier chain guard mounting. 3. Install chain idler with welded on spacer (#2) and chain idler (#3) with 1/2” nut (#8). 4. Assemble the spacer (#4) and reduction sprocket ...