(600 recommended) 182 'a' min. 100 1010 696 168 'a' 300 min. (600 recommended) min. 100 964 664 170 'a' 300 min. (600 recommended) SP520 'X' 'X' a d c b A B C D E SP420 480 240 566 558 1158 SP520 840 280 554 546 1146 SP920 480 240 566 558 1158 A B MAN AUTO ON OFF S4 S3 S2 S1 ON OFF S3 S2 S1 SP520 SP420 SP920 SP420 SP520 & SP920 7 8 9 10 a b a b 11 12 10a SP520 SP420 SP920 X Y A B C SP520 & SP920 Wall Fires Models: SP420, SP520 & SP920 IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RE

The heater should not be connected until the instruction leaflet is read fully. Recessed Installation Please note that this appliance can also be wall-mounted so that it is recessed. This can be installed in a large fireplace opening or a purpose built wall. See Table 1 for size of recess required and hole fixing dimensions and Fig. 5a. This fireplace insert does NOT require venting. In order to ensure it’s future safety in use, it is essential that this fire is securely fixed to the wall. IT IS

7. Manual Operation - SP520 The switches are located at the bottom right side of the heater -see Fig. 6. Remote Operation The standby switch (S1) must first be turned ‘ON’ (and the ‘AUTO/MAN’ Switch turned to ‘AUTO’ - SP420 & SP920). Note: It takes some time for the receiver to respond to the transmitter. DO NOT PRESS the buttons more than once within two seconds for correct operation. Manual & Remote Operation Setting Operation Setting Flame Effect only Press the ‘ I ’ button (Switch 3) Top Neo

OPERATION Initializing The Remote Control 1. Turn on the electrical power at the circuit breaker. 2. Slide open the battery cover on the back of the remote transmitter. 3. Install three AAA batteries into the remote control. Replace the battery cover. Note: The LCD display will flash when new batteries are inserted. 4. Move the remote transmitter close to the fireplace (less than five feet preferred). Press any button on the remote control. The remote is transferring the code to the receiver bui

High heat setting Set switches 1 and 2 to ON. All three elements will glow and, when the temperature selected on the electronic control dial 3 is reached, two of the elements will automatically turn off, switching back on if the temperature falls. The fire can be returned to low heat setting by pressing switch 2 to OFF. See also ‘Electronic economiser temperature control ’ below. Electronic economiser temperature control This sensitive output control 3 will switch the radiant heater elements ON

WARNING – DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL. WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A FIXED SOCKET OUTLET. FOLLOW these instructions carefully. NEVER cover or obstruct in any way the heat outlet slots at the top of the heater. THE HEATER CARRIES A WARNING ‘DO NOT COVER’ TO ALERT THE USER TO THE RISK OF FIRE THAT EXISTS IF THE HEATER IS ACCIDENTALLY COVERED. WARNING – THE SAFETY GUARD ON THIS APPLIANCE CONFORMS TO THE

This heater is designed for permanent installation only, care should be taken to install according to the following instructions. All required clearances should be maintained, in addition all electrical wiring and connections should comply with local electrical codes. Note : It is extremely important to read all information labels. Care must be taken to ensure that the heater is rated the same voltage as the electrical supply wires. Failure to do so could result in unsafe heater operation as wel

Supply wire must be of two wire plus ground variety, with a rating capable of handling all heaters on the circuit. Supply wire should be rated for a minimum of 60C. Make electrical connection according to relevant diagrams shown on Figure # 2. Make connections using approved wire nut connectors and secure the grounding wire to the green ground screw on the heater chassis. On models with Register Style Front Grills only, a terminal box cover plate is provided. Insert the tabs of the cover plate i

The warranty will not apply if, in the sole judgement of the Company, damage or failure has resulted from accident, alteration, misuse, abuse, incorrect installation, or use for purposes other than a Dimplex electric fireplace. The foregoing is in lieu of all other warranties expressed, implied or statutory, and the company neither assumes, nor authorizes any person to assume for it any other obligation, or liability in connection with sold product. CONSERVER CE MANUEL POUR LE CONSULTER AU BESOI

The warranty will not apply if, in the sole judgement of the Company, damage or failure has resulted from accident, alteration, misuse, abuse, incorrect installation, or use for purposes other than a Dimplex electric fireplace. The foregoing is in lieu of all other warranties expressed, implied or statutory, and the company neither assumes, nor authorizes any person to assume for it any other obligation, or liability in connection with sold product. CONSERVER MANUEL POUR LE CONSULTER AU BESOIN.C