Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
High heat setting Set switches 1 and 2 to ON. All three elements will glow and, when the temperature selected on the electronic control dial 3 is reached, two of the elements will automatically turn off, switching back on if the temperature falls. The fire can be returned to low heat setting by pressing switch 2 to OFF. See also ‘Electronic economiser temperature control ’ below. Electronic economiser temperature control This sensitive output control 3 will switch the radiant heater elements ON and OFF to accurately maintain the level of comfort that you have selected. Select low or high radiant setting – then turn the control dial to 7; when the room reaches a comfortable level of warmth, turn the dial down until the electronically controlled elements switch off. The control dial should be left at this setting; the electronic control will then switch the elements ON and OFF as needed to maintain your chosen comfort level. 3 1 4 5 • MIN MAX 1 2 3 4 5 2 Fig. 2 4 6 5 Fig. 3 Convector Heater – see Fig. 3 The 800 watt convector heater can be used by itself for background heating, or in conjunction with the radiant elements for extra heat. The convector output is through the vent in the canopy. This vent must never be covered or obstructed. The convector heater is controlled by an ON/OFF switch 4 and thermostat 5 located at the top right-hand side of the fire. The output may be set to any position between MIN and MAX settings. Set the switch to ON and set the thermostat to maximum setting initially. When the room is warm enough, turn the thermostat down slowly until the convector heater just clicks off. The thermostat will switch the convector ON and OFF to maintain the selected temperature setting, as indicated by the pilot light 6. In the MIN position, the convector will switch ON at a temperature of approximately 5°C, to help protect against frosty conditions. NOTE: If the convector heater does not come on when the thermostat is set to a low number, this is normally because the room is warmer than the thermostat setting and is not a fault. 2 Maintenance WARNING: ALWAYS DISCONNECT FROM THE MAINS SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE Access to flicker rotors and lamp replacement – see Fig. 4 The fuel effect is secured by two screws, one at each end. Slacken these screws (do not remove them completely) until the fuel effect is released, then lift it clear. Ensure that the screws are partially inserted into the fuel effect before refitting it. Each flicker rotor should sit horizontally on its pin and spin freely without fouling its mounting bracket. If necessary, adjust the bracket by bending slightly (the plastic diffuser material is flexible). Ensure flicker rotors To replace a lamp, bend up the defective lamp’s flicker rotor top bracket arm carefully and lift off the rotor. Replace the defective lamp with a 60 watt B22 fuel-effect lamp. Reassemble in reverse order, ensuring that the diffuser/top bracket arms are positioned correctly and the flicker rotors spin freely. rotate freely on pins and that lamps are in sockets correctly Fig. 4 Removing the guard – see Fig. 5 Unscrew the two screws at each end of the guard, then withdraw the lower edge of the guard first. Refit the guard in reverse order. Fig. 5 Removing the radiant elements – see Fig. 6 First remove the guard, as detailed above. The element holders are spring loaded. To remove an element, grip one end using a soft cloth to protect the surface, then push carefully but firmly to one side until the other end disengages from its socket. Withdraw the element carefully. Refit in reverse order. Fig. 6 Cleaning the reflector – see Fig. 7 The reflector may be more easily cleaned if the elements are first removed (see above). Wipe the reflector with a warm soapy cloth, then buff with a soft dry cloth. DO NOT use abrasive cleaning powders or metal polish. Fig. 7 3 Cleaning WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. Do not use detergents, abrasive cleaning powder or polish of any kind on the body of the heater. Allow the heater to cool, then wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean off stains. Be careful not to allow moisture into the heater. After Sales Service Your appliance is guaranteed for 1 year from the date of purchase. We undertake to repair or exchange, free of charge within the guarantee period, any part found to be defective, excluding lamps. Your rights under this guarantee are additional to your statutory rights, which in turn are unaffected by this guarantee. If your appliance is not working correctly, please contact our Customer Helpline on 0870 727 0101. This guarantee only applies in the United Kingdom. Specification subject to change without prior notice. This appliance complies with European Safety Standards EN60335-2-30 and European Standards EN55014, EN60555-2 and EN60555-3 for electromagnetic compatibility. These standards cover the requirements of EEC Directives 73/23 an...