Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
(600 recommended) 182 'a' min. 100 1010 696 168 'a' 300 min. (600 recommended) min. 100 964 664 170 'a' 300 min. (600 recommended) SP520 'X' 'X' a d c b A B C D E SP420 480 240 566 558 1158 SP520 840 280 554 546 1146 SP920 480 240 566 558 1158 A B MAN AUTO ON OFF S4 S3 S2 S1 ON OFF S3 S2 S1 SP520 SP420 SP920 SP420 SP520 & SP920 7 8 9 10 a b a b 11 12 10a SP520 SP420 SP920 X Y A B C SP520 & SP920 Wall Fires Models: SP420, SP520 & SP920 IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: If the appliance is damaged, check immediately with the supplier before installation and operation. Do not use this heater in the immediate surroundings of a bath, shower or swimming pool. Do not use outdoors. Do not cover or obstruct the heater in any way. Overheating will result if it is accidentally covered. In the event of a fault unplug the heater. Unplug the heater when not required for long periods. The supply cord is recommended to be placed on the right hand side of the heater. The heater can also be HARD wired - this is recommended if the heater is recessed - see ‘Recessed Installation’. This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance. If the supply cord is damaged it must be replaced by the manufacturer or service agent or similarly qualified person in order to avoid a hazard. Electrical WARNING – THIS APPLIANCE MUST BE EARTHED This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage. Do not switch the appliance on until properly installed. Please read all the safety warnings and operating instructions. General Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier. Contents of Carton • Heater. • Wall fixing bracket. • Fixing screws and wall plugs. • Remote control and batteries (AAA’s type). • Spare bulb. Do not connect the heater to an electricity supply until it is installed on a wall correctly - see ‘Installation’. SP420 & SP920 - When in operation there is a 300 watt heat output from the fuel effect, and an additional 120 watt output when the heated glass panel is in operation. SP520 - When in operation there is a 300 watt heat output from the fuel effect, and an additional 200 watt output when the heated glass panel is in operation. The heater can be used remotely or manually - see ‘Operation’. General features of remote control are: • Activate/Deactivate heated glass panel. • The illumination of fuel effect can be increased or decreased. Please note: Used in an environment where background noise is very low, it may be possible to hear the motor which operates the flame effect. This is normal and should not be a cause for concern. Installation Do not connect appliance until properly fixed to the wall and the Instruction leaflet is read fully. The minimum distances must be observed. For installation of the appliance, care must be taken not to damage concealed cables. Please be careful while drilling the holes. This model is designed to be permanently fixed to a wall at a minimum height of 300mm. The wall bracket must be fitted horizontally and the cable routed to the bottom right of the heater as in Fig. 1. A height of 600mm from bottom of heater to floor is recommended for optimum viewing of fuel bed (see Fig. 2 for recommended fixing dimensions). For optimum viewing mark the top four screw fixing positions on wall in accordance with the recommended fixing dimensions -see Fig. 2. Drill holes with a 6mm drill bit. Fix the wall bracket using the plugs and screws provided see Fig. 3. Carefully lift the heater up ensuring that the top rear ledge of heater engages the wall bracket and is sitting centrally positioned. - see Fig. 4 (b). Rotate the bottom fixing bracket down. - see Fig. 4 (c). Gently bring the heater level with the wall. - see Fig. 4 (d). Mark the bottom hole position (see Fig. 5), remove the heater ensuring that the bottom fixing bracket is rotated up. Drill and fit wall plug. Refit the heater to the wall fixing bracket (i.e. follow steps as in Fig. 4 a, b, c and d) and rotate the bottom fixing bracket down again and use the screw provided to permanently fix the heater in place. The heater should not be connected until the instruction leaflet is read fully. Recessed Installation Please note that this appliance can also be wall-mounted so that it is recessed. This can be installed in a large fireplace opening or a purpose built wall. See Table 1 for size of recess required and hole fixing dimensions and Fig. 5a. This...
Эта инструкция также подходит к моделям:Камины - (SP5) SP520 (960.6 kb)
Камины - (SP9) SP920 (960.6 kb)