Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
WARNING – DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL. WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A FIXED SOCKET OUTLET. FOLLOW these instructions carefully. NEVER cover or obstruct in any way the heat outlet slots at the top of the heater. THE HEATER CARRIES A WARNING ‘DO NOT COVER’ TO ALERT THE USER TO THE RISK OF FIRE THAT EXISTS IF THE HEATER IS ACCIDENTALLY COVERED. WARNING – THE SAFETY GUARD ON THIS APPLIANCE CONFORMS TO THE REQUIREMENTS OF BS1945 1971 AND SATISFIES THE HEATING APPLIANCES (FIREGUARD) REGULATIONS 1978. THE GUARD IS TO PREVENT THE RISK OF FIRE OR INJURY FROM BURNS AND SHOULD NEVER BE REMOVED PERMANENTLY. If young children, the aged or infirm are likely to be left in the vicinity of the heater, we advise that adequate precautions should be taken. We recommend that a guard be fitted to ensure contact with the heater is avoided and objects cannot be inserted into the product. For further information, please contact our guard supplier direct on Tel No 01603 667957, or in case of difficulty or for further advice contact the Customer Helpline – see page 4. This heater is designed to meet the requirements of the relevant British and European Standards for safety. However, we do not recommend its use directly on deep pile carpets or long haired rugs. CAUTION – DO NOT position curtains or furniture or other inflammable materials closer than 1 metre (39") in front of this heater - see also page 4. CAUTION – DO NOT use this heater where excessive dust or moisture is present. CAUTION – DO NOT use this heater in conjunction with an external thermal control, a programme controller, a timer or any other device which switches on the heater automatically, since a fire risk exists when the heater is accidentally covered or displaced. Important Safety Advice Preparing for use Unpack the heater carefully and retain the packaging for future use, in the event of moving or returning the heater to your supplier. Always ensure that the heater is stood on a firm, level surface. IMPORTANT - see Fig. 6, page 4 for clearance dimensions. See also ‘Important Safety Advice’. Electrical connection WARNING – THIS APPLIANCE MUST BE EARTHED This heater must be used on an supply only and the voltage marked on the heater must correspond to the supply voltage. This heater is fitted with a rewirable plug incorporating a 13 amp fuse. When replacing the fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used. If the plug is not suitable for your socket, remove it and fit an appropriate plug. IMPORTANT: If the plug is not suitable for your socket, the 13 amp plug should be removed. Before wiring the appropriate plug, please note that the wires in this mains lead are coloured in accordance with the following code: BLUE – NEUTRAL BROWN – LIVE GREEN & YELLOW – EARTH As the colours of the wires in the mains lead of this appliance may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: Connect the BROWN wire to the terminal marked ‘L’ or coloured RED. Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK. Connect the GREEN & YELLOW wire to the terminal marked ‘E’ or ‘ ’ or coloured GREEN or GREEN & YELLOW. If in doubt, consult your electrician. IMPORTANT: If the mains lead is damaged, it must be replaced by a special lead or assembly available from Dimplex or an authorised Dimplex service agent. Before switching on Remove the fuel effect (two screws ) and check that the lamps and flicker rotors are positioned correctly - see Fig 2, page 3. The flicker rotors should sit horizontally on their pins and spin freely without fouling their mounting brackets. If necessary, adjust the bracket by bending slightly. Refit the fuel effect by inserting the front edge first, then secure it with the two screws. Ensure that all packing items are removed (read any warning labels carefully) and that the fuel effect and radiant elements are positioned correctly, otherwise damage may occur. Operating position IMPORTANT — READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE Operation When you are certain that you have completed the installation, plug in and switch on at the wall socket. Controls - see Fig. 1 Fuel effect The fuel effect will be lit all the time that the heater is connected to the power supply, even if the heat selector switches are in the OFF position. The flicker rotors should begin to rotate after a minute or so. The lamps will go out only when the heater is switched off at the wall socket or unplugged. Radiant elements You have a choice of low heat (two elements, 1332W) or high heat (three elements, 1998W). Both settings have electronic temperature control - see below. A switch is set to ON when the red dot is visible. Low heat setting Press switch 1 to ON. Two elements will glow and, when the temperature selected on the electronic control dial 4 is reached, one of the elements will automatically turn off, switch...