Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
7. Manual Operation - SP520 The switches are located at the bottom right side of the heater -see Fig. 6. Remote Operation The standby switch (S1) must first be turned ‘ON’ (and the ‘AUTO/MAN’ Switch turned to ‘AUTO’ - SP420 & SP920). Note: It takes some time for the receiver to respond to the transmitter. DO NOT PRESS the buttons more than once within two seconds for correct operation. Manual & Remote Operation Setting Operation Setting Flame Effect only Press the ‘ I ’ button (Switch 3) Top Neon Flame Effect & Heat On Press the ‘ I ’ button again (Switch 3) Bottom Neon The Standby switch must first be turned ‘ON’ to operate the heater manually or by remote control. Note: It takes some time for the receiver to respond to the transmitter. DO NOT PRESS the buttons more than once within two seconds for correct operation. To go to the previous settings press the O button. Pressing the O button on the remote turns off the light & heat settings. To resume press the I button until the desired setting is reached - see Fig. 8. To increase or decrease the brightness of the flames, use the dimmer button or the button on the Remote Control. The heat setting will remain the same. To turn off the power the Standby Switch must be turned ‘OFF’. Lamp Replacement - SP420 WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS. Warning -The lamps reach high temperatures during operation. For this reason, allow the lamps to cool down after switching off the appliance. The front panel will need to be removed in order to change lamps –see Fig. 10. Warning - The front panel is heavy and easily damaged. The front panel is fixed with 4 spring loaded pins (see ‘a’ in Fig. 9) and is supported at the top by the chassis. To gain access to lamps please apply the following procedure: While holding the front panel by its sides with both hands, carefully pull forwards the panel at the bottom until the pins detach from the clips - see Fig. 9. When the bottom holding pins are undone, carefully pull forwards at the top until the top pins detach and then lift the front panel up and out (see Fig. 10). To gain access to the bulbs remove the screws at ‘A’ to remove the cover bracket ‘X’ - see Fig. 10a. For access to the bottom bulbs, carefully slide the flexible rotisserie (see ‘a’ in Fig. 11) to one side ensuring that the rubber grommet is not lost (see ‘b’ in Fig. 11). Remove the defective lamp by unscrewing it (see Fig. 11). Replace with a 60W E14 SES Clear Candle bulb, rotating it. Take care not to over-tighten the lamp. Steps for reassembling the heater 1. Refit the rotisserie making sure that the rubber grommet is carefully pushed into the slotted hole on the axial bracket. 2. Replace the cover bracket ‘X’ - see Fig. 10a. 3. Replace the front by aligning the slots on the front frame and making sure that it catches fully on the support brackets. Lamp Replacement – SP520 & SP920 WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS. Warning -The lamps reach high temperatures during operation. For this reason, allow the lamps to cool down after switching off the appliance. The front panel will need to be removed in order to change lamps – see Fig. 12. Warning -The front panel is heavy and easily damaged. The front panel is supported at the top by the chassis and held tight by magnets at the top and bottom on the SP520 model. On the SP920 the front panel is held at the bottom by a fixing screw. To gain access to lamps please apply the following procedure: Remove the fixing screw from the base of the front frame on the SP920 - see Fig. 12. While holding the front panel by its sides with both hands, carefully tilt the bottom of the frame outwards until free and then lift the panel up (1) and then away (2) from the main body - see Fig. 12. To gain access to the bulbs remove the screws at ‘A’ to remove the cover bracket ‘X’ and the screws at ‘B’ to remove the cover bracket ‘Y’ - see Fig. 10a. For access to the bottom bulbs, carefully slide the flexible rotisserie (see ‘a’ in Fig. 11) to one side ensuring that the rubber grommet is not lost (see ‘b’ in Fig. 11). Remove the defective lamp by unscrewing it (see Fig. 11). Replace with a 60W E14 SES Clear Candle bulb, rotating it. Take care not to over-tighten the lamp. Steps for reassembling the heater 1.Refit the rotisserie making sure that the rubber grommet is carefully pushed into the slotted hole on the axial bracket. 2.Replace the cover brackets ‘X’ and ‘Y’ - see Fig. 10a. 3.Replace the front by aligning the slots on the front frame and making sure that it catches fully on the support brackets. The magnets on the chassis will hold the front flush to the main body (SP520). 4. Replace the fixing screw on the base of the front frame (SP920). Cleaning WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. For general cleaning use a soft clean duster – never use abrasive cleaners. The glass viewing screen should be cleaned carefully with a soft ...
Эта инструкция также подходит к моделям:Камины - (SP4) SP420 (960.6 kb)
Камины - (SP5) SP520 (960.6 kb)