CONTENTS 1. PREFACE 1.1 SAFETY PRECAUTIONS...........................................................................................................................3 1.2 FEATURES.................................................................................................................................................3 1.3 DIMENSIONS .............................................................................................................................................3 1.4 SPECIFICATIO

has Determined that this product meets the ENERGY STAR® guidelines for energy efficiency. (Except DH30E) FOR YOUR RECORDS Write the model and serial numbers here: FOR YOUR RECORDS Write the model and serial numbers here: Safety Precautions.....3 Operating Instructions.................5 Installation Instructions.................8 Care and Maintenance ..............9 Troubleshooting Tips............................10 Warranty.....Back cover Customer Assistance Numbers ....Back cover You can find t

Does not defrost control. Defrost control is defective. Check defrost control, replace it. 4. Insufficient dehumidification Low relative humidity Turn dehumidifier off. Poor air circulation Move dehumidifier to obtain free and unobstructed air circulation. H/E clogged with dust and dirt Clean evaporator and/or condenser assembly Air filter is dirty. Clean it. Motor is not operating. Check Motor, repair or replace it. —18— CONDITION CAUSE REMEDY 5. Noisy operating Fan If cracked, out of balance,

Cleaning the front case bucket and cabinet Clean the front case and the cabinet with a soft cloth, warm water, and a mild detergent. Do not use bleach or abrasives. Cleaning the air filter 1-1. First pull out the air filter by pressing the filter hooks lightly. Then release two tabs at the bottom side of the filter. 1-2. Wash air filter with warm water and a mild detergent. Rinse and dry it. Replace it in place. Cleaning the coil 2-1. Remove air filter from the cabinet regarding to the above. 2-

Power --- Operation starts when this button is pressed and stops when the button is pressed again. Humidity Control --- This button controls the humidity in the room. • : To raise the humidity setting • : To lower the humidity setting • The humidity setting can be set to a permanent "On" setting or to a specific humidity setting between 35% and 70% in 5% increments. "On" setting - dehumidifier runs continuously regardless of humidity condition. 35% - 70% setting - dehumidifier shuts on and off a

ASSEMBLY MAXIMUM WORKING TIME: 0.2 ~ 0.7 sec. RETURN TIME: 60 sec. – OUTSIDE DIMENSIONS W x H x D, mm(in) PROTECTOR OPEN : 32°F(0°C ) CLOSE : 52.6°F(13°C ) – OPEN : 32°F(0°C ) CLOSE : 53.6°F(13°C )+ 3 – 3 + 2 – 3 + 3 – 3 + 2 – 3 OPEN : 28.4°F(-2°C ±2) CLOSE : 55.4°F(13°C ±2) OPEN : 26.6°F(-3°C ±2) CLOSE : 55.4°F(13°C ±2) OPEN : 28.4°F(-2°C ±2) CLOSE : 55.4°F(13°C ±2) DH3010B (DHA3012D*) DH4010B (DHA4012D*) DH5010B (DHA5012D*) . ..NOTE : Specifications are subject to minor change without notice f

DESCRIPTION PART NO. Q'TY PER SET REMARKSDH4010B DH5010B 1 POWER CORD ASSEMBLY 6411A20001Q 1 S, A 2 SWITCH, ROTARY 6600A20001A 1 S 3 MOTOR ASSEMBLY SINGLE 4681A20040A 1 S 4 CAPACITOR 0CZZA20001Q 1 S 5 COMPRESSOR (ROTARY) 2520UABC2FA 5416AR2179J 1 S 6 O.L.P. 6750U-L039A 1 S 7 LAMP, NEON 6912A30001F 1 S 8 THERMOSTAT 2H01127K 2H01127J 1 S 9 HUMIDISTAT 5216A20001A 1 S, A 10 SWITCH ASSEMBLY, MICRO 6600A30003C 1 S . S: SERVICE PARTS A: ALTERNATE PARTS N: NOT SERVICE PARTS —9— 3.1 MECHANICAL PARTS 3.1.

Close valves A and B, and observe vacuum gauge for a few minutes. A rise in pressure would indicate a possible leak or moisture remaining in the system. With valves A and B closed, stop the vacuum pump. 4) Remove the hose from the vacuum pump and place it on the charging cylinder. See Figure 22B. Open valve C. Discharge the line at the manifold connection. 5) The system is now ready for final charging. 7. Recharge as follows : 1) Refrigeration cycle systems are charged from the High-side. If the

Those required minimum clearances are set forth in the picture below. Please keep the following instructions in mind when installing in a closet or recessed area: • Consider allowing additional clearance for installation and servicing. • Wall, door and floor molding may necessitate additional clearances. • An additional inch of clearance is recommended to minimize noise transfer. • Consider space needed for companion appliances. • For closet installations, the picture below shows the minimu

You might see a sudden increase or decrease in operation time if the sensor determines more or less drying is required. This is not a malfunction. Time Dry Use TIME DRY to select heat level and drying time manually. This can be used if clothes are not as dry as you like them at the end of the cycle. Use TIME DRY for heavy and bulky items and thick work. TABLE OF CONTENTS PART 1. SPECIFICATIONS ...................................................................................................