Оценок - 2, средний балл: 3 ( )

Производитель: Goldstar Размер: 12.13 mb Название файла: Язык инструкции:

Those required minimum clearances are set forth in the picture below. Please keep the following instructions in mind when installing in a closet or recessed area: • Consider allowing additional clearance for installation and servicing. • Wall, door and floor molding may necessitate additional clearances. • An additional inch of clearance is recommended to minimize noise transfer. • Consider space needed for companion appliances. • For closet installations, the picture below shows the minimum required ventilation openings for the door. A louvered door with comparable ventilation openings is also acceptable. 3" (7.6 cm) _ 48"2, (310 cm2) i 24"2 (155 cm2) 3" (7.6 cm) _ - ventilation hole 114" max \ (35.6 cm) \ 18" t (45.72 cm) ventilation hole Closet Door 0" (0 cm) |1"H— 29.96"-HrI (2.54 cm) (76.1 cm) (2.54 cm) Closet-side View ■ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ (68.6 cm) Closet-front View * 0" (0 cm) 11 INITIAL STEPS FOR INSTALLING YOUR DRYER Once in position, adjust the leveling legs of the dryer until it is level from left to right and front to back. The leveling legs must remain firmly on the floor and the dryer should not rock. The maximum slope of the dryer from left to right or front to back should not exceed 2.5 cm (1 inch). If the dryer is not level, and if the slope exceeds 2.5 cm (1 inch), a load may not tumble properly and internal sensors may malfunction. Note: Other sections of this manual also provide important information concerning the placement of and clearances for your dryer. Please review this entire manual before proceeding with any installation. 1 STEP 2 Procedure for Reversing the Door The door on your dryer can be installed to open either to the left or the right. Follow these instructions to reverse the direction in which your door opens: Noie^ Door and latch should be aligned at the center when closed. 2 12 Part 3l INITIAL STEPS FOR INSTALLING YOUR DRYER STEP 3 Connecting the Exhaust and Venting System. i!L WARNING! • Use a heavy metal vent. • Do not use plastic or thin foil duct. • Clean old ducts before installing this dryer. • Failure to follow these instructions can result in death or fire. Note^ The exhaust must be vented to the outside. Improper taping and incorrect installation will cause dryer malfunction. In addition to the following warnings, please refer to manual section on Exhaust Requirements and Maintenance. Warning: The dryer must be vented to the outdoors. Please follow the instructions (and all others in this manual) very carefully. Failure to follow these instructions can result in death or fire. ' Do not use plastic or thin foil duct. ' Rigid or semi-rigid metal ducting is recommended for use as transition ducting between the dryer and and the wall. In special installations when it is impossible to make a connection with the above recommendations, then a UL-listed flexible metal transition duct may be used between the dryer and wall connection only. The use of this ducting will affect dry time. ' Position the dryer such that the exhaust duct run is as short as possible. ' Clean old ducts before installing this dryer ' The male end of each section of exhaust duct must point away from the dryer. ' Use as few elbow joints as possible. ' Use duct tape on all duct joints. ' Insulate ductwork that runs through unheated areas in order to reduce condensation and lint build-up on pipe walls. ■ PLEASE BE AWARE THAT FAILURE TO EXHAUST THE DRYER CORRECTLY WILL VOID THE DRYER’S WARRANTY. ■ ALTERNATE EXHAUST DIRECTIONS 1. Remove screw and exhaust duct. (Use exhaust kit part #3911EZ9131X.) matches the desired venting direction (Right side not available on Gas Dryers) 2-2. Connect a short piece of duct to the blower housing and attach the duct to the base. 3-1. Insert the male end of a 4" elbow into the female end of a short duct. Tape the joint. c .....<..... N DUCT TAPE \ w ^ r j 3-2. Insert this assembly elbow first through the hole in the dryer and push the female end of the elbow onto the male end of the blower output shaft. Tape the joint. 13 INITIAL STEPS FOR INSTALLING YOUR DRYER STEP 4 Connection of Gas Supply STEP 5 Electrical Plug Connections (Gas dryer only). In addition to the following, please refer to manual section on Gas Requirements and Instructions. 1. New stainless steel flexible connector. Use this type of connector only if allowed by local codes. Use Design AGA Certified Connector. 2. 1/8" NPT Pipe Plug (for checking inlet gas pressure) 3. Equipment Shut-Off Valve Installed within 6’ (1.8 m) of dryer. 4. Iron Pipe. Shorter than 20’ (6.1 m) Use 3/8" pipe. Longer than 20’ (6.1 m) - Use 1/2" pipe. 5. 3/8" N.P.T. Gas Connection. Note^ Make sure the burner orifice is proper for the type of gas you have. For instance, using LPG with LNG orifice will result in death, fire or explosion. Or using LNG with LPG nozzle will not allow the burner to ignite. I...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: