Failure to do so can result in fire or electrical shock. Prepare minimum 5 ft (1.52 m) of length in order for dryer to be replaced. First, strip 3 ‘/2 inches (8.9 cm) of outer sheath from end and strip 1 inch of insulation from each conductor. Then, put the hooked shape end of the wire under the screw of the terminal block (hooked end facing rightward) and pinch the hook together and tighten the screw securely. gr ^ 1. Connect neutral wire (white) of power cord to center terminal block scre

INSTALL THE AIR CONDITIONER IN THE WINDOW a. Carefully lift the air conditioner and slide it into the open window. Make sure the bottom guide of the air conditioner drops into the notches of the L bracket. See Figure. 27. IMPORTANT : When the air conditioner drops into the L bracket, the air conditioner will be centered in window opening as shown in Figure. 28. b. While steadying the air conditioner, carefully bring the window sash down behind the upper guide of the air conditioner, as shown in

You might see a sudden increase or decrease in operation time if the sensor determines more or less drying is required. This is not a malfunction. Time Dry Use TIME DRY to select heat level and drying time manually. This can be used if clothes are not as dry as you like them at the end of the cycle. Use TIME DRY for heavy and bulky items and thick work. TABLE OF CONTENTS PART 1. SPECIFICATIONS ...................................................................................................

Safety Precautions Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

6-4. Remove the hose from the vacuum pump and place it on the charging cylinder. See figure 23B. Open valve C. Discharge the line at the manifold connection. 6-5. The system is now ready for final charging. 7. Recharge as follows: 7-1. Rotary compressor systems are charged from the high-side. If the total charge cannot be put in the high-side, the balance will be put in the suction line through the access valve which is installed as the system is opened. 7-2. Connect the charging cylinder as sho

ASSEMBLY MAXIMUM WORKING TIME: 0.2 ~ 0.7 sec. RETURN TIME: 60 sec. – OUTSIDE DIMENSIONS W x H x D, mm(in) PROTECTOR OPEN : 32°F(0°C ) CLOSE : 52.6°F(13°C ) – OPEN : 32°F(0°C ) CLOSE : 53.6°F(13°C )+ 3 – 3 + 2 – 3 + 3 – 3 + 2 – 3 OPEN : 28.4°F(-2°C ±2) CLOSE : 55.4°F(13°C ±2) OPEN : 26.6°F(-3°C ±2) CLOSE : 55.4°F(13°C ±2) OPEN : 28.4°F(-2°C ±2) CLOSE : 55.4°F(13°C ±2) DH3010B (DHA3012D*) DH4010B (DHA4012D*) DH5010B (DHA5012D*) . ..NOTE : Specifications are subject to minor change without notice f

(1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours Cancel) • The Setting Temperature will be raised by 2°F(1°C) 30min. later and by 2°F(1°C) after another 30 min. -STARTING OPERATION • Everytime you push this button, when the unit is not operating, timer is set as follow. (1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours Cancel) POWER • To turn the unit ON, push the button. To turn the unit OFF, push the button again. • Thi

has Determined that this product meets the ENERGY STAR® guidelines for energy efficiency. (Except DH30E) FOR YOUR RECORDS Write the model and serial numbers here: FOR YOUR RECORDS Write the model and serial numbers here: Safety Precautions.....3 Operating Instructions.................5 Installation Instructions.................8 Care and Maintenance ..............9 Troubleshooting Tips............................10 Warranty.....Back cover Customer Assistance Numbers ....Back cover You can find t

Child Lock Child Lock can be used to prevent your children from changing options on control panel while the dryer is running. When Child Lock is enabled, all the buttons will be locked and Child Lock glows. To enable Child Lock, Press and hold OPTION for 3 seconds, A single beep tone is heard and Child Lock is displayed on the status window. To disable Child Lock, press and hold OPTION for 3 seconds again. i!L WARNING! • For better drying performance and safety, clean lint filter every si

Safety is foremost---both your own and that of other people. Many important safety instructions are provided in this instruction and your appliance. Always read and observe all safety instructions. 1 Remove pedestal, installation hardware, and instructions from the shipping carton. 2 Position the washer/combo on top of the pedestal. NOTE: Because of the weight of the washer/combo, two or more people may be needed. NOTE: If the washer or combo was previously installed, unplug it, disconnect the i