37826 Rev. 9 ©2006 Fluke Corporation, All rights reserved. Printed in U.S.A. All product names are trademarks of their respective companies Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 Table of Contents Section 1: General Information ...................................................................................... 1-1 1.1 Introduction .................................................................................................. 1-1

This efficient, handheld Analyzer satisfies a wide range of external pacemaker testing. Table 1-1 describes the symbols used on the instrument. Table 1. Symbols Symbol Description A Important information; refer to manual. A Hazardous voltage I Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website for recycling information. G N10140 Conforms to relevant Australian EMC requirements Conforms to relevant Canadian and US standards C€ Conforms to European Union di

The program will be generated and the display will show the first step. 8. Press the Name [F6] key to edit the name of the program. See next section, Chapter 4, Changing the Name of a Program, for creating a user-defined program name. Local Operation Menu Changing the Name of a Program 1. The name of an existing program is changed from the Program Menu. From the Main Menu (press PREVIOUS until the Main Menu appears), press Menu [F6] | Program [F4]. In addition to changing the name of an existing

Materials for Cleaning the High Range Piston Cylinder 1. Prepare a clean work area near a running tap water source. 2. Prepare several sets of folded wipers as shown in Figures 6-2 through 6-4. Two wipers can be folded together for wiping the outside of the piston and cylinder. Prepare several twisted wipers as shown in Figures 6-10 through 6-12 to wipe the bore of the cylinder. 3. Disassemble the piston/cylinder assembly. 4. Insert the retaining clip from the bottom of the piston into the insta

FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. Since some countries or states do not. allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other decision-maker of

For preprogrammed recording, the VCR needs the following data, which must be stored in a TIMER block: - Date for recording - Program number of the transmission - Start/stop time for recording These data can be copied directly to the VCR from the corresponding program survey of the teletext service. The PDC (RCF Recorder Control Function) data transmitted via Teletext automatically enable correct recording of the required program. For PDC test purposes this pattern generator offers page numb

2, 3/99 © 1998, 1999 Fluke Corporation, All rights reserved. Printed in Germany. All product names are trademarks of their respective companies. Please note In correspondence concerning this instrument, please quote the type number and serial number as given on the type plate. Bitte beachten Bei Schriftwechsel über dieses Gerät wird gebeten, die Typennummer und die Gerätenummer anzugeben. Diese befinden sich auf dem Typenschild an der Rückseite des Gerätes. Noter s.v.p. Dans votre corresp

The result is a reduction in cross color interference and an improvement in the picture quality. The R-G-B output offers the primary colors red, green, and blue including composite sync and sub-carrier signals at 5 BNC sockets at the rear side. Service is done at the component level, so it is not necessary to exchange a complete module. In addition the mechanical concept allows quick access to all parts for service purposes; all units are plugged into the motherboard. (GB) 2-2 GENERAL PM 541

Output: 8-bit parallel Protocol: Centronix Signal levels: TTL compatible Fixed Serial Interface Settings: 9600 Baud, 8 data bits, no parity, 1 stop bit Handshake: XON / XOFF LIMITED WARRANTY & LIMITATION OF LIABILITY Each Fluke product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is one year and begins on the date of shipment. Parts, product repairs and services are warranted for 90 days. This warranty extends only to the orig

All rights reserved. Printed in The Netherlands. All product names are trademarks of their respective companies Using the Interface Cable PC Requirements - USB 1.1 (or higher) port on the PC. - Windows XP/ 2000/ Me/ 98 Second Edition. Installing the USB- IR cable drivers - Log into an account with Administrator privileges (Windows XP or Windows 2000). - Plug the USB cable into an USB port. - Windows will respond that it has "found new hardware", and the Windows Hardware Wizard dialog will appear