Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Position the upper chimney so that it can be fixed via the holes on the side of the ‘Y” bracket on the ceiling (refer to Figure 11). Connecting the Screen (SU 202 Only) Before attaching the screen the power unit wipe the face of the flange to ensure there is no Figure 11 5 Figure 12 Figure 13 grit present – if there is this will most definitely crack the glass. The plastic washers must be positioned between the screw head and the glass. Fit the screen – please have someone hold this in place whilst another person puts in the screws. Using FINGERS ONLY, tighten the screws evenly until finger tight. Do not under any circumstances use a screw driver. Re-Circulating Requirements If the unit will be used in re-circulating mode (refer Figure 12), Figure 14 fit the deflector (refer Figure 13) with the screws supplied to the upper telescope chimney. There are holes in the back upper edge of the decorative chimney for this purpose. A short length of ducting is connected between the exhaust outlet on the fan and the deflector to direct the air back into the kitchen through the vents at the top of the upper decorative chimney. The carbon filter (supplied separately) that absorbs odors is installed behind the aluminium grease filter (refer to Fig 14) O P E R A T I N G P R O C E D U R E S Read all the instructions before operating the appliance. Save these instructions for future reference. General Advice Ensure that the grease filters are in place. Without these components, operating blowers could catch on to hair, fingers and loose clothing. Keep fan, filters and surfaces clean of grease and fat. Always turn hood fan ON when cooking. NEVER leave cooking unattended. 6 NEVER dispose cigarette ashes, ignitable substances or any foreign objects into blowers. Cooking that generates flame is not recommended as this hood is equipped with a thermal overload that will shut down the motor if it senses excessive heat. When frying, oil in the pan can easily overheat and ignite. Heat oil slowly in an appropriately sized pot (covering the entire burner) to reduce the risk of boiling over and burning In the event of a range top grease fire, observe the following: Switch OFF the range hood. Turn off the cook top then smother flames with a close fitting lid, cookie sheet or other metal tray. If the flames do not go out immediately. EVACUATE AND CALL THE FIRE DEPARTMENT. Never pick up a flaming pan – you may be burned. DO NOT USE WATER including wet dishcloths or towels, as a violent steam explosion may occur. Functions Modular Wall Range Hood Controls A: Light ON/OFF button B: Blower Speed 1 (low) or OFF C: Blower Speed 2 (medium) D: Blower Speed 3 (high) E: Blower Speed 4 (intensive) F: 10 Minute Timer Filter requires washing indicator: after 30 hours of use, all the buttons will light up to remind you that the grease filter should be cleaned. Follow the instructions for cleaning filters in this booklet. Once the grease filters have been cleaned and replaced, reset by pressing the timer button (F). Do not rely solely on this indicator. Generally, the grease filter should be washed on a regular basis to avoid grease filter fires. The blower should be turned on for approximately 5 minutes before cooking in order to establish air currents upward through the hood. Use the low speeds for normal use and the higher speeds for strong odors and fumes. M A I N T E N A N C E The range hood should provide many years of trouble free use provided it is properly maintained. Be sure the lights are cool before cleaning the hood – they are halogen and become extremely hot. Cleaning the Filter The aluminium mesh filters should be washed by hand or in the dishwasher as required. Damaged and worn filters must be replaced immediately. (Do not operate blower when filters have been removed). 7 Allow filters to dry before replacing them, otherwise water will be drawn into the blower. If a carbon filter has been fitted, this must be replaced every 6 months as a minimum, depending on usage and type of cooking that is performed. It is suggested that a spare set of carbon filters is kept on hand. These can be ordered from the supplier of your range hood. Cleaning the Hood The outside and interior of your hood should be wiped regularly with a clean, damp cloth and mild household dish detergent or degreaser. Use a good quality non-abrasive foaming type stainless steel cleaner for exterior surfaces. Follow the manufacturers directions. Generally the foam is sprayed onto a clean dry cloth and then applied to the stainless steel. Allow the foam to react on the surface for a few minutes and then wipe with a clean dry cloth. On the surfaces that are exposed directly to heat from the cook-top, it is advisable to clean these regularly to avoid the deposits from becoming baked on. Do not use abrasive cleaning agents as these will destroy the brushed finish. Light Bulb Replacement (If in doubt, call 866-528-4987) Turn blower and lights off. Make sure the lights are cool. D...
Эта инструкция также подходит к моделям:Вентиляторы - SU202 (264.72 kb)