Войти:
Оценок - 4, средний балл: 3.8 ( )

Инструкция по эксплуатации Precor, модель M9.41s

Производитель: Precor
Размер: 134.02 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Important: If you are installing both handrail options, install a handrail on one side before proceeding to the other side of the treadmill. Attach the front portion of the handrail first. This helps you determine where to position the lower handrail clamp. Electronic console Bolt End clamp Center clamp Handrail end cover Upper frame Finger guard Rear roller Bolt Attaching the front section of the handrail. Diagram 2 Upright support Handrail Guide rail Side rail Nut plate C O M M E R C I A L P R O D U C T S D I V I S I O N 4. Place the center clamp on the front portion of the handrail, followed by an end clamp. See Diagram 2. Align the two clamps with the handrail mounts on the upper frame. 5. Insert a bolt through each clamp. See Diagram 2. Using the supplied 3/16" hex key, screw each bolt through the handrail until the clamp is snug against the upright support. Do not fully tighten the bolts until you have installed the lower end of the handrail. 6. To mount the lower portion of the handrail, locate the lower handrail clamp, star washer, and lower handrail clamp bolt. Refer to Diagram 3 while taking the following steps: Note: If you are installing both handrail options, perform the following steps on one side of the treadmill before proceeding to the other side. a. Slide the handrail nut plate along its guide rail until the hole in the nut plate is aligned with the handrail mounting hole. b. Put one star washer on the lower handrail clamp bolt. For ease of assembly, set the bolt on the floor near the nut plate. c. Place the lower portion of the handrail into the clamp and align the bolt hole. d. Pick up the bolt set aside in step 6b. and insert the bolt through the lower handrail clamp and handrail mounting hole. e. Guide the lower handrail clamp onto the nut plate. Slide the clamp and nut plate along the guide rail to find the equilibrium point. Attaching the lower handrail and handrail clamp. Diagram 3 Handrail Nut plate Lower handrail clamp C O M M E R C I A L P R O D U C T S D I V I S I O N f. To secure the handrail inside the clamp, use the 5/32" hex key provided. Do not overtighten the bolt or damage may occur to the clamp. Note: After extensive use, vibrations from the treadmill may cause the bolts to loosen. You may need to periodically inspect the bolts and, if necessary, tighten both the upper and lower handrail clamp bolts using the hex keys provided. g. Return to the upper handrail clamps and securely tighten the bolts using the 3/16" hex key. Note: If you are installing both handrails, repeat assembly steps 1 through 6 to attach the handrail to the other side of the treadmill. Precor Incorporated Precor is a registered trademark of Precor Incorporated. P/N 36643-102 P.O. Box 3004 “C” is a trademark of Precor Incorporated. 8/96 Bothell, WA USA 98041-3004 ©1996 Precor Incorporated. Specifications subject to change without notice. 1-800-4-PRECOR ...

Эта инструкция также подходит к моделям:
Тренажеры - C940 (134.02 kb)
Тренажеры - C942 (134.02 kb)
Тренажеры - M9.45 (134.02 kb)
Тренажеры - c944 (134.02 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории