(1.25 kPa) 12” W.C. (3.00 kPa) Manifold Pressure - High 3.8” W.C. (0.95 kPa) 11” W.C. (2.74 kPa) Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 3.3” W.C. (0.82 kPa) Orifi ce Size #44 DMS - 0-2000ft #45 DMS - 2000-4500ft #54 DMS Minimum Input Altitude 0-2000 ft. (0-610m) 12,500 BTU/h (3.66 kW) 10,500 BTU/h (3.07 kW)Minimum Input Altitude 2000-4500 ft. (610-1372m) 10,500 BTU/h (3.07 kW) Maximum Input Altitude 0-2000 ft. (0-610m) 22,500 BTU/h (6.59 kW) 21,500 BTU/h (6.30 kW)Maximum Input Altitude 200

Regency Quality The Regency name means quality in every way. The product is created and built in a world class manufacturing facility focused on getting every detail just right. Represented across North America by a carefully selected professional retail network; you can rely on knowledgeable dealers and installers who understand how to make our products run safely and to the optimum performance. Exceptional Fire The essence of each and every Regency fireplace is the unique flame. With its danci

The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram, see manual. FPI Direct Vent (Flex) System Termination Kits include all the parts needed to install the P33 using a fl exible vent. ImportantWhen installing Cabinet Mantels: the wall thimble must be secured first and venting must be attached to unit before sliding into final position. Snorkel Terminations Snorkel Terminations: FPI Kit # Length Contains: #946-513 2 Feet 1) 6-5/8” flexible l

This could cause high temperatures and may present the possibility of a fire. b) The location of the horizontal vent termination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. See "Exterior Vent Termination Locations" section for more details. 7) Ensure that the pipe clearances to combustible materials are maintained (Diagram 5). Install the termination cap. Note: If installing termination on a vinyl siding covered wall, a vinyl siding

Your Ultimate fire can be turned up as high as 40,000 BTU providing high efficiency heat or turned down to 15,000 BTU to enjoy the fire view with less warmth. Replace your old wood- stove, install into your existing masonry fireplace or warm up your kitchen, bedroom or den as you lower heating bills. Ultimate U38/U39 Gas Stove 4 Ultimate U39 gas stove with optional nickel door and louvers The clean, modern lines of the Ultimate Gas stove wrap around its extraordinary fire. Your Ultimate fire can

Make sure wood is not stacked directly on the ground, it may absorb moisture from the ground. It should be allowed to dry in these conditions for a minimum of six months, preferably one year or more. IT MUST BE UNDERSTOOD THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED. Your stove will not operate at the level that it is meant to unless you use seasoned, dry wood. Do not burn driftwood or wood that has been in salt water, doing so will void yo

This versatile fireplace can be installed almost anywhere in your home to provide up to 18,500 BTU of consistent, controllable heat, operating even during power outages. Enjoy multiple styling options: choose sleek flush panels or traditional full screen doors, one of 3 realistic brick styles, or stainless steel inset panels to match your home décor. Specifications Natural Gas Propane Input (BTU) 18,500 17,500 Turn Down to (BTU) 12,500 14,500 EnerGuide Rating* 61.60% 64.32% Efficiency (stea

Attach the flexible vent to the adapter as follows (see also Figure 42): A. Install the Inner Flex Pipe 1. Install the small gear clamp loosely around the inner flexible vent pipe, push it back out of the way. 2. Apply a bead of Mill-Pac Black (700°F) high temperature sealant - Catalog No. 10K81) to the inner adapter collar, approximately ... inch from the end. 3. Pull and extend the inner flexible vent pipe. 4. Slide the inner flex pipe over the adapter collar. Ensure the flexible vent pipe com

Installations at Altitudes of 0 to 4500 ft.Units are tested and approved for elevations of 0 to 4500 feet (0 to 1372 meters). Installations at Altitudes above 4500 ft.For elevations above 4500 feet (1372 meters), install the unit according to the regulations of the local authorities having jurisdiction and, in the USA, the latest edition of the National Fuel Gas Code (ANSI Z223.1) or, in Canada, the latest edition of the CAN1-B149.1 and .2 codes. Table 1shows the units' gas orifice size for the

Route Flex Vent Ensure that the flex vent is properly routed to provide the required clearance. Do Not allow the flexible vent to bend in a radius tighter than 5" (127 mm). Refer to Figure 43. Support horizontal sections of flex with metal straps at 2 foot (0.61 m) intervals. Step 4. FIELD WIRING Step 4. FIELD WIRING A. SIT and Honeywell Millivolt Wiring (See Figure 44 )– 1. Select any of the following optional controls: appliance-mounted (rocker switch) or wall-mounted switch, thermostat, or on