Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Make sure wood is not stacked directly on the ground, it may absorb moisture from the ground. It should be allowed to dry in these conditions for a minimum of six months, preferably one year or more. IT MUST BE UNDERSTOOD THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED. Your stove will not operate at the level that it is meant to unless you use seasoned, dry wood. Do not burn driftwood or wood that has been in salt water, doing so will void your warranty. Do not burn treated wood, coal, garbage, cardboard, solvents, or colored paper. Burning treated wood, garbage, solvents, or colored paper may result in the release of toxic fumes. This type of burning will also void your warranty. Break-in PerioD If your stove has a Gold or Nickel-Plated Door, be sure to clean it with Windex brand glass cleaner and a very soft cloth to remove any fingerprints and residues prior to the first fire and before any fire if the gold has been handled or soiled. Do not close the door tightly during the “Break-in Period.” Also, open the door frequently (every 5-10 minutes) to keep the gasket from adhering to the curing paint. Ventilate the house well during these first firings as the paint gives off carbondioxideandunpleasantodors.Itisrecommendedthat persons sensitive to an imbalance in the indoor air quality avoid the stove during the curing process. Please be patient with the heat output of your stove for the firstfewweeks.Thesteelwillgothroughacuringprocessthat eliminates moisture, which is deep in the steel and firebrick. This moisture will reduce initial heat output of your stove and may make it difficult to start. After you have broken in the paint on the stove it will be necessary to build hot fires to thoroughly remove the moisture from the appliance. Running the stove with the draft fully open for 1 to 1-1/2 hours after starting and adding generous amounts of fuel during the first week or two should complete the curing process. We recommend the use of a thermometer attached to the stovetop or chimney. Temperatures on the connector pipe should run in the250-600 degree range. (DO NOT OVER FIRE THE STOVE DURING THIS PROCESS. IF THE STOVE OR CHIMNEY BECOMES RED, REDUCE THE AMOUNT OF AIR ENTERING THE STOVE IMMEDIATELY). PainT curing Your new Canyon™ C310 is painted with Forest High Temperature Paint that cures during the first few firings. We recommend that you put your stove through a regimen of three burns. The first two should last for 20 minutes each at 250 degrees (the stove should be allowed to cool completely between each burn). The third should be a burn of at least 450 degrees F. for 45-60 minutes. The paint will become soft, gummy and emit non-toxic smoke during these burns. After the stove cools down for the third time, the paint will harden. DO NOT BUILD A LARGE ROARING FIRE UNTIL THIS CURING EFFECT IS COMPLETE OR YOU MAY DAMAGE THE FINISH OF YOUR STOVE. Spray can touch-ups should be done only with Forest brand paint, available from a Lennox Hearth Products dealer. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Brick insTallaTion canyon™ c310 Brick insTallaTion CAUTION: Wear gloves during brick installation in case of sharp edges behind the stove. Note: Installation of baffle bricks and ceramic blanket is much easier when you can still access the flue outlet, as in before installing the insert. Be sure the insulating blanket is placed flat on the bricks so as not to block the flue and that it does not hang out over the front of the baffle. Use a ruler or a piece of kindling to reach back over the blanket to be sure it is flat on top of the baffle bricks all the way back. Install bricks #1-30 in the numbered sequence. (Note: Bricks 22-25 lean up against the lower air channeland butt against bricks 17-21 on the bottom of the stove) Next install bricks 35-40 on top of the stainlesssteel secondary tubes in the upper part of the firebox. These bricks fit up against bricks 26-30 on the backwall and should rest on the rear two stainless steel tube spports running front to rear down the cemter of thestove. Included in your stove are two 13”x17”x1” thick ceramic fiber blankets. Install a ceramic fiberblanket on top of each of these sets of two sets of three bricks making sure the blanket is pushed fully tothe rear. Next install bricks 41-46 under the ceramic fiber blanket and on top of the front two stainlesssteel secondary tubes. (Caution: Make sure that the front of the ceramic fiber blanket does notproject beyond bricks 41-4 .) WARNING: IF THE BRICKS AR NOT INSTALLED EXACTLY AS SHOWN THEY COULD FALL OUT OF PLACE DURING REFUELING OR BURNING OF THE STOVE CAUSING SERIOUS INJURY. canyon™ c310 Brick Sizes (see Figures on this page) Side View A = -7/8 x 8- /4” M Brick B = -1/2 x 4-1/2” 1/2” C = -1/2 x 9” D = 1-1/2 x 4-1/2” E = -7/8 x 9” F = 4-1/2 x 9” M 4-1/2” G = x9” H = -1/2 x 4-1/2” J = 4-1/2 x 7” K = x 7” M -4-1/2 x 4-1/2” Insulating Blanket Size is 1/2” x 11” x 20” and...
Эта инструкция также подходит к моделям:Камины - CANYON C310 (359.87 kb)
Камины - CANYON C310 (359.87 kb)
Камины - CANYON C310 (359.87 kb)