341785 REV1 08-03-2009 Low Head Room Front Mount Torsion Spring Installation Instructions and Owner’s Manual 9800 Series - 4 Section IMPORTANT NOTICE! Read these instructions carefully before attempting installation. If in question about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. Wayne-Dalton Corp. P.O. Box 67 Mt. Hope, OH 44660 Definition of key words used in this manual: INDICaTEs a POTENTIally hazaRDOus sITuaTION WhICh

If in question about any of the procedures, do not perform the work. Instead, have a trained door systems technician do the installation or repairs. IMPORTANT SAFETY NOTICES An overhead door is a large heavy object that moves with the help of springs under high tension. Moving objects and springs under tension can cause injuries. For your safety and the safety of others, follow these instructions: 1. Wear protective gloves during installation to avoid possible cuts from sharp metal edges. 2. It

WARNING WINDING BARS MUST FIT SNUGGLY INTO HOLES IN SPRING WINDING CONES. ATTEMPTING TO WIND SPRINGS WITH LOOSELY FITTING RODS, SCREWDRIVERS OR OTHER IMPROPER TOOLS CAN RESULT IN SEVERE OR FATAL INJURY. Feed the cable attached to the left hand bottom bracket up the vertical track, behind the rollers and secure to the left hand drum. Push the drum up against the end bearing bracket and secure to the shaft by tightening the set screws (solid shafts use 1/4” key(s) and set screws to secure drums).

Press the counter gear onto the end bracket until snaps engage. Select the right hand counter cover assembly and align the hex of the counter cam with the end of the winding shaft. Also, align the “0” on the counter cover with the raised rib on the end bracket. Press the counter cover assembly against the counter gear until it locks into place. Repeat for left hand side for double spring applications. NOTE: No drive gear, counter gear or counter cover assembly is required on left hand side for s

• SIZES UP TO 42' WIDE AND 26' HIGH • VARIETY OF PATTERNS AND MATERIALS • EXTREMELY DURABLE CONSTRUCTION Wayne-DaltonRollingGrillesaredesignedtomaximizesecurity,visibility,andventilation.Thedurableconstructiontechniqueusedensuresthatthegrilleswilloffermanyyearsofreliableandconsistentperformance. Materials&ConstructionStandardfeaturesinclude5/16”galvanizedsteelhorizontalrods,continuousfromjambtojamb,andcoveredwithaluminumtubes.Verticallinksarealuminum.Endlinksensurethatthegrillecannotbepulledfrom

Attach to section using (2) 1/4”-20 x 7/8” self drilling screws at each end and center stile location. To attach a u-bar across the lower leaf of hinges with strut clips: Remove 1/4”-20 x 7/8” self drilling screws from lower leaf of hinges along sections which a u-bar will be attached to. Place u-bar above across hinges and attach to section with strut clips and the 1/4”-20 x 7/8” self drilling screws which were removed. 8300 LT-coM Aluminum Strutting Schedule---White, Almond, and Taupe colored

Mark a vertical pencil line on the mounting surface above the door, at the center. Measure from the center of the bearing, in one of the end bearing brackets, downwards, to the top the door. Using that measurement, measure that distance upwards from the top of the door to the mounting surface, and mark a horizontal pencil line which intersects the vertical pencil line. Align the edge of the center bearing bracket with the vertical pencil line and the center of the bearing in the center bearing b

backRoom RequiRemeNT: Backroom is defined as the distance needed from the opening back into the garage to allow the door to open fully. weather Seal (may Not be included): Cut or trim the weather seal (if necessary) to the header and jambs. Align the header seal with the inside edge of the header and temporarily secure it to the header with equally spaced nails. Next, fit the jamb seals up tight against the header seal and flush with the inside edge of the jamb. Temporarily secure the jamb seals

Painting Your Garage Door suRfACE PREPARATION fOR PAINTING Wax on the surface must be removed or paint peeling/ flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a fine steel wool pad saturated with soapy water. A final wipe and rinse should be done with clean water only to remove any loose particles and any soapy film residue. Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or no. 4

To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the find a Dealer section online at Attaching hor Tracks to Q.I. flag Angles Tools: Ratchet wrench, 9/16” Socket, 9/16” Wrench, level, Step ladder 14 NOTE: If you have Q.I. flag angles, complete this step. To install horizontal track, place the curved end over the top roller of the top section. Align key slot of the horizontal track with the Q.I. tab of the flag angle. Push curved portion of horiz