Pay close attention to all warnings and notes. This manual MUST be attached to the wall in close proximity to the garage door. Copyright 2007 Wayne-Dalton Corp. Part No. 325809 Rev.3 7/19/2007 FOR RESIDENTIAL SECTIONAL OVERHEAD GARAGE DOORS ONLY! DO NOT USE ON ONE PIECE DOORS! IMPORTANT! THE DOOR AND OPENER WILL NOT FUNCTION PROPERLY UNTIL INFRARED SAFETY SENSORS ARE INSTALLED AND PROPERLY ADJUSTED! GARAGE DOORS & OPENERS Keychain/Visor Transmitter (1 or 2) Entrapment Label Light Diffuser Opener

If the system engages with the door in the open position, personal items that are left unattended in the garage or home are at risk to theft. To insure the safekeeping of these items, close the garage door. Typical signs of an engaged system: Single spring system: Visually inspect the TorqueMaster® Plus right hand end bracket to confirm that the system has engaged (see illustration). If the system is engaged then the door will not close. If the opener force settings were properly set during the

LIMITED WARRANT . The Manufacturer warrants that its door and its hardware fittings will be free from defect in workmanship and material. Should any defects in workmanship or material appea . within ONE YEAR of delivery, manufacture shall, upon notification, correct such nonconformity at its option, by repairing or replacing any defective part or parts. See maintenanc . and painting instructions for prepainted steel doors listed below or contact Wayne-Dalton Distributor for a copy of the mainten

NOTE: Do not tighten 1/4”-20 flange nuts to opener studs at this time. You will be instructed when to tighten them in the idrive® main installation and owners manual. Remove the temporary orange label holding the antenna wire. Straighten antenna wire and angle it 45 degrees to the right. NOTE: Do not coil the antenna wire. This will reduce the radio signal range. Power Drill 1/8” Drill Bit 7/16” Socket Driver 45 angle Antenna wire Mounting surface (Header) TOP OF DOOR SUPPORT BRACKET 1/4” X 1-1/

This manual MUST be attached to the wall in close proximity of the door. WINDLOAD RATED DS-350 COMMERCIAL ROLL-UP DOORS INSTALLATION INSTRUCTIONS ©Copyright 2002 Wayne-Dalton Corp. P/N 291341, DOC #101-0093-1 REV 02 IMPORTANT SAFETY NOTICES Read the enclosed instructions carefully before attempting installation. If there are any questions about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. 1. Operate the door ONLY when it is

This will prevent the door from raising or lowering while installing the rear support. Using perforated angle, 2” lag screws and 5/16” bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16”-18 x 1-1/4” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door. ^WARNING! KEEP HORIZONTAL TRACK PARALLEL AND WITHIN 3/4” OF DOOR EDGE, OTHERWISE DOOR COULD FALL, RESULTING IN

IF THE INSERT SHEET INSTRUCTIONS ARE NOT INCLUDED, CONTACT WAYNE-DALTON CORP. FOR A FREE COPY. If removing an existing door, carefully follow the directions given on the insert sheet instruction in the portion titled “Removing the Old Door”. ¿^WARNING! REMOVAL OF AN EXISTING DOOR CAN BE DANGEROUS. FOLLOW INSERT SHEET INSTRUCTIONS CAREFULLY, OTHERWISE SEVERE OR FATAL INJURY COULD RESULT Begin the installation of the door by checking the opening. It must be the same size as the door. Vertical ja

Ensure the door rollers are rotating freely when opening and closing the door. If rollers do not rotate freely, clean the door tracks, removing dirt and any foreign substances. Clean and lubricate (use a non-silicon based lubricant) hinges, steel rollers and bearings. DO nOT lubricate plastic idler bearings, nylon rollers, door track. DO nOT oil a cylinder lock, if actuation is difficult use a graphite dust to lubricate. 6 Please Do not Return This Product To The Store. Contact your local Wayne-

If in question about any of the procedures, do not perform the work. Instead, have a trained door systems technician do the installation or repairs. IMPORTANT SAFETY NOTICES An overhead door is a large heavy object that moves with the help of springs under high tension. Moving objects and springs under tension can cause injuries. For your safety and the safety of others, follow these instructions: 1. Wear protective gloves during installation to avoid possible cuts from sharp metal edges. 2. It

IMPORTANT: THE OPENER MUST BE CONNECTED TO A PROPERLY GROUNDED 3 PRONG, 120 VOLT OUTLET. The opener can be permanently wired. To permanently wire the unit, see permanent wiring option on page 20. Plug the power cord into the closest grounding type receptacle. Excess power cord length must be routed and contained safely away from any moving parts. As soon as power is applied to the opener, the light on the opener will blink once to indicate a successful self-check of the controls. WARNING Outlet