ON OFF BLAST On/Off Control Switch Used to start and stop the spinner. (Emergency Stop-OFF Position) Starting the Motor WARNING Before starting the spreader, the driver shall verify all bystanders are a minimum of 25 feet away from operating spreader. 1. Set the power switch to the ON position to start the motor. The motor will start immediately. The power switch will remain in this position. Blast Position Move and hold the power switch to the BLAST position for as long as momentary operation i

2 Control Functions ......................................................................pg. 4 Discrimination Points ................................................................pg. 5 Searching ..................................................................................pg. 7 Pinpointing ................................................................................pg. 9 Zero Motion Pinpoint Mode ..................................................pg. 9 Pinpointing in the Motion Search M

Subject to improvement or modification without notice. WEIGHT Fisher Research Laboratory does not warrnt suitability to specific use. Fisher Research Laboratory shall in no event be liable for any direct, incidental, consequential or indirect damages. 3.5 lbs. LENGTH Extended ....................................................................52” 2 Collapsed.....................................................................42” 2 FREQUENCY VLF-Search.............................................

94431 LOW PROFILE TAILGATE SPREADERS Owner’s Manual CAUTION Read this manual before installing or operating the spreader. This manual supersedes all editions with an earlier date. This manual is for FISHER® Low Profile Spreaders with serial numbers Model 1000 - (10003 -) Model 2000 - (20364 -) TABLE OF CONTENTS PREFACE ..................................................................................................................................1 SAFETY INFORMATION ............................

This warranty does not cover external fi nish (except at date of original purchase) or labor costs not specifi cally authorized by Fisher Manufacturing Company. A full and complete copy of our One Year limited warranty is available upon request. #8253 - Service Sink Faucet: Long Spout with Wall Bracket, Vacuum Breaker, Polished Chrome #2445 - Service Sink Faucet: Short Spout, Vacuum Breaker, Polished Chrome KEEP THIS MANUAL FOR FUTURE REFERENCE ANSI/A112.18.1M, ANSI/NSF 61.9 fisher manufacturing

39101 REV. B /-/^/-/ETF? FISHER MANUFACTURING C □ M RAN Y 4” C/C Backsplash Pre-Rinse Unit Product Installation Guide #2610 - Pre-Rinse Unit: 4” C/C Backsplash Control Valve, Ultra Spray Since 1936, Fisher Manufacturing Company has manufactured heavy-duty, high quality plumbing products and hardware specialties for the food service industry. For three generations, the Fisher family has adhered to a strict dedication of and overall value. When you install Fisher products... you install the b

During this period Fisher Manufacturing Company will replace a defective product or part without charge to you, provided that the entire product is delivered to Fisher Manufacturing Company. All transportation and insurance charges for shipping the product to and from Fisher Manufacturing Company must be borne by you. Charges for transportation and insurance may, at the option of Fisher Manufacturing Company, be refunded depending upon our investigation of the warranty claim. This warranty does

41157 REV. B 10456 LUBE 2000-5000 WASHER 2000-3002 2000-5003 BIBB CAP SEAT WASHER 1000-7502 SEAT SCREW 3000-0011 RH SWIVEL STEM 3967 16” SWING SPOUT 3964 14” SWING SPOUT 3963 12” SWING SPOUT 3962 10” SWING SPOUT 3961 8” SWING SPOUT 3960 6” SWING SPOUT 12564 2.2 GPM AERATOR 19119 SWIVEL SPOUT RETRO-FIT KIT 2932-0002 IN-LINE CHECK VALVE 2949-9001 SCRUB BRUSH 1792 ANGLE STOP WITH KEY 1790-1 ANGLE STOP W/ CROSS HANDLES 2400-2103 ELBOWS 10014 (24”) 10022 (36”) SUPPLY LINE 1/2” F x 1/2” F 10049 (24”)

Use only with a Power Wheels® 12 Volt Lead-Acid Rechargeable Battery and Power Wheels® 12 Volt Charger with Type “12V” Connector (included). “CD Player” requires three “AA” (LR6) alkaline batteries (not included) for operation. JEEP and the Jeep grille design are registered trademarks of DaimlerChrysler Corporation and are used under license. ©DaimlerChrysler Corporation. Fisher-Price, Power Wheels by Fisher-Price, BARBIE, Cruisin’ Tunes, Power Lock and Power Stick are U.S. trademarks of Mattel

• Use pipe thread sealant such as PST on all threaded joints. • Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier. Tools Required for Installation • Medium Sized Crescent Wrench • Pipe Thread Sealant • Phillips Screwdriver • 7/16” Drill Bit Installation Instructions READ BEFORE INSTALLATION: Before removing any existing T&S, Chicago, CHG, or Dormont hardware, read the instructions on next page labeled “EZ Install Adapter Instructions