Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
41157 REV. B 10456 LUBE 2000-5000 WASHER 2000-3002 2000-5003 BIBB CAP SEAT WASHER 1000-7502 SEAT SCREW 3000-0011 RH SWIVEL STEM 3967 16” SWING SPOUT 3964 14” SWING SPOUT 3963 12” SWING SPOUT 3962 10” SWING SPOUT 3961 8” SWING SPOUT 3960 6” SWING SPOUT 12564 2.2 GPM AERATOR 19119 SWIVEL SPOUT RETRO-FIT KIT 2932-0002 IN-LINE CHECK VALVE 2949-9001 SCRUB BRUSH 1792 ANGLE STOP WITH KEY 1790-1 ANGLE STOP W/ CROSS HANDLES 2400-2103 ELBOWS 10014 (24”) 10022 (36”) SUPPLY LINE 1/2” F x 1/2” F 10049 (24”) 10006 (36”) SUPPLY LINE 1/2” M x 1/2” F 2949-8600 CUP WASHER ISHER ISHER ISHER PST Installation Instructions for Pre-Rinse Units BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION REGARDING BACKFLOW PREVENTION Installation Notes: • Be sure to shut off water supply before beginning. • Use pipe thread sealant such as PST on all threaded joints. • Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier. Tools Required for Installation • Medium Sized Crescent Wrenches • Pipe Thread Sealant • Phillips Screwdriver • 7/16” Drill Bit • 1/8” Allen Wrench Installation Instructions 1. Insert the gasket into the groove on the concentric. Making sure the gasket is in place, loosely mount the concentrics and fl ange onto the control valve body. 2. Mount the small riser to the control valve body using thread sealant. Screw the add-on faucet to the other end of the small riser, again using thread sealant. 3. Mount control valve body to the backsplash by inserting the concentrics through the backsplash and attaching slip joints. Attach elbows or supply lines and tighten concentrics. Be sure to use pipe thread sealant on all threads. 4. Mount the pipe to hose adapter to the enclosed riser using thread sealant. Mount the other end of the riser to the female outlet of the add-on body. 5. If no wall bracket is to be installed, proceed to Step 6, otherwise do the following: a. Locate and drill a O7/16” hole in the wall directly behind and about 3/4 the way up the riser pipe. b. Loosely attach the front and back of the pipe clamp onto the riser pipe. c. Hold the wall bracket fl ange against the wall, centered with the hole. Use the wall screws and a screw driver to mount the fl ange to the wall. d. Slide part, but not all, of the wall bracket rod nonthreaded end fi rst through the center hole of the fl ange and into the wall. e. Align the rod with the pipe clamp and thread the rod into the pipe clamp. Be sure the rod is level by adjusting the pipe clamp position. f. Once level, fi x the rod in place by tightening both the set screw located in the fl ange and the pipe clamp screws. 6. Slip the hose hook over the pipe to hose adapter. Using thread sealant and a crescent wrench, thread the SS hose into the pipe to hose adapter. 7. Install gooseneck spring by slipping SS hose through the spring. Spring will fi t over adapter which holds it in an upright position. Note: Be sure spring is installed as shown. DO NOT INSTALL SHORT BEND DOWN. Step 1 Step 2 Step 3 Gasket Concentric Flange 7 3/4” - 8 1/4” [196.9 - 209.6mm] Thread Sealant Goes Here Slip Joints O7/8” PREVENTER BACK-FLOW WATTS N9 ISHER ISHER ISHER ISHER ISHER ISHER ISHER ISHER ISHER 8. Fit one of the handle gaskets inside the outlet of the insulated handle and mount the spray valve onto it. 9. Fit the other handle gasket inside the inlet of the insulated handle and mount the handle onto the SS hose. If installing backfl ow preventer, attach it between the SS hose and insulated handle. Be sure that gaskets are used on both sides of the backfl ow preventer 10. If installing a brush, do so by pressing brush into the bumper of the spray valve until secure. 11. To install swing spout to add-on faucet, apply o-ring lube to the o-rings on the swing spout. Make sure the white snap ring is in place before mounting the swing spout. Mount the swing spout and tighten the swing spout nut onto the add-on faucet spout outlet. 12. Turn on water supply and check for leaks. Installation Instructions Continued Step 7 Step 8 Step 9 Step 10 Step 11 Step 5 Step 6 Step 4 Thread Sealant Goes Here Spring Bend On This Side Handle Gasket Apply O-Ring Lube Here Swing Spout Handle Gasket Excess Rod Length Trim to Fit (optional) Pipe Clamp Riser Pipe Set Screw Wall Screw Wall Thread Sealant Goes Here Step 12 ...