ITEMS INCLUDED 1) UL & cUL Listed Condensate Pump with 6' power cord 1) Check Valve to prevent backflow of liquid into the unit 1) Overflow Safety Switch (Models 20+ULS and 20+ULST only) 1) 20 Feet of 3/8" I.D. Plastic Tubing (Models 20+ULT and 1) Instruction Sheet ULST only) MODELS AVAILABLE MODEL VOLTAGE CURRENT PART NUMBER DESCRIPTION 20+UL 115VAC/60Hz 1.45 Amps 46296901 Base Model 20+ULS 115VAC/60Hz 1.45 Amps 46296902 Base Model with Overflow Safety Switch 20+ULT 115VAC/60Hz 1.45 Amps 462969

NOT CSA CERTIFIED FOR SOLID FUELS. The regulator contained in this package is manufactured with careful precision. It is designed to regulate chimney draft with a high degree of accuracy and fuel efficiency. English .......Page 1 Francais .....Page 4 Espanol ......Page 6 INSTALLATION OF TEE SECTION Locate the draft control as near to the furnace or boiler as possible. If the installation has a smokepipe stack control, locate the regulator at least 18" away from the stack control. (See Figures 3-

1706 Canterbury Rd Greenville, NC 27858 Ph. 252.355.6789 Oysterdoctor@aol.com Efficiency Of Bacterial Disinfection By A Duct Mounted UV-AireO Air Purifier For: Table of Contents Table of Contents Background ..........................................................................................................................3 Organism.........................................................................................................................3 Testing Structure.....................

With ClearWave™, the electric field generated is always being applied to the water, while a magnetic field relies on the movement of water to produce the electric potential changes. Low frequency waveforms are emitted through two coiled wires attached to the outside of the water pipe. As a result of these waveforms, the two coils are constantly inducing a voltage into the water in the area of the ClearWave™. When one coil induces a positive voltage the other coil induces a counteracting negative

(see Figure 1) For pipe mounting, the wall mount tabs should be removed from the mounting brackets. (see Figure 2) 2. Plug the antennas into each end of the housing, to the appropriate wire wrap connections (e.g. “CW” for clockwise wrapping and “CCW” for counter clockwise wrapping). If longer wires are needed, up to 50 feet of 12Ga stranded wire can be added to the antenna wires with an insulated butt end wire connector or they Page 2 Page 3 can be replaced with 70 feet of 12Ga stranded wire. PR

is the most advanced hi-tech computerized anti-scale device available today. It operates by using a programmed ‘chip’ to constantly cycle through and induce over 200 different electro-magnetic low frequency wave pulses into the water. These wave pulses produce water with remarkable anti-scale properties, without adding salts or chemicals, at an operating cost for electricity of approximately $5.00 US per year. POWER SPECIFICATIONS: 18 VAC, 5 Watts,.09 Amps PRODUCT QUESTIONS PHONE FIELD FIRST for

Over a thirty day period, the moisture content was measured at weekly intervals. Homes with the Eliminator installed saw a reduction of moisture levels to as low as 16% and 17%. A wood moisture level of 20% or less is considered ideal. Homes without the Eliminator showed no reduction in moisture content. “The Eliminator performed well, even under severe moisture problem conditions… the amount of air moved is sufficient to correct the problems present.” Cliff Consulting Columbia, S.C. Moisture Co

Hold in place and install the supplied flat washer and hex nut. After all four (4) mounting brackets are installed, tighten nuts. (See Figure 4) Figure 1 Figure 3 Figure 4 Figure 2 MOUNTING LOCATION AND MOUNTING REQUIREMENTS 1. Locate fan on crawl space vent areas that do not have good cross flow ventilation. 2. The ELIMINATORTM fan unit must be mounted onto an existing or new crawl space vent that has a grill mesh construction. (see mounting instructions) 3. One unit is recommended per 1,000 sq

Ninety (90) days UV lamps/bulbs Provisions: 1. During the limited warranty period, Company, or its authorized service representative, will repair or replace, at Company’s option, without charge, a defective Product. Product that is repaired may be repaired with new or refurbished replacement parts. Product that is replaced may be replaced with a new or refurbished product of the same or similar design. Company will return repaired or replacement Product to customer in working condition. Labor ch

By maintaining constant air flow through the crawl space, problems such as fungus growth, dry rot, and radon gas will be reduced or eliminated. An integral temperature switch allows fan operation only at air temperature above 50°F. EL-1 UNIT INCLUDES: 120 volt ELIMINATOR™ fan unit with integral temperature fan control and mounting hardware. OPTIONAL CONTROL: EDH Eliminator™ De-Humidistat: 120 volt De-Humidistat to allow operation of fan at a set humidity level of the crawl space. READ THESE INST