If the host device is a Modem like device and has a RS232 DCE port, then use a "straight cable". That is, connect the signals with the same name from one side to the other. DCE TXD IR100S-L TXD RXD RXD RTS RTS CTS CTS DSR DSR DTR DTR CD CD RI RI GND GND - 15 - Version 1.20 May 27, 2002 ACT-IR100SL and IR100SL-M User’s Manual If the host device is a PC like device and has a RS232 DTE port too, then you need to use a "Null Modem" connection between the two. That is, in/out signal pairs need to be

15. Choose Print, the LED on IR100M+/IR100MP will be on and printer begin to print out. Or the parallel LED on the top of IR100M will flash and printer beginning to print out. If not, see Trouble Shooting. TROUBLE SHOOTING AND COMPATIBLE PRINTERS LIST For help on general and miscellaneous problems you may be experiencing with your printing, refer to the following pages for possible solutions. Look up your problem and try the solution. Note: Please Check your printer is on the IR-100M+/IR100M/IR1

IR100M adapter does provide two-way-communication capability and its returned signals are received but dropped by O.S. and therefore, not compatible with MFP. However, there are exceptions, such as Brother MFC4350 and other brands/models." IR100M series compatible with any interface of IEEE 1284 Type B. If printer is equipped with 2 interfaces, ONLY 1 interface could work each at time, both interfaces don’t work simultaneously. When your Printer connected to an USB port, the Parallel port will n

48511 Warm Springs Blvd, Suite 206 Fremont, CA 94539, USA TEL: (510) 490-8024, FAX: (510) 623-7268 E-Mail: irda-support@actisys.com Web: FCC & VCCI Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING-FCC Regulations state that any unauthorized chang

ACTiSYS Corp. 48511 Warm Springs Blvd, Suite 206 Fremont, CA 94539, USA TEL: (510) 490-8024, FAX: (510) 623-7268 E-Mail: irda-support@actisys.com Web: ....: IR-100M FCC & VCCI Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING-FCC Regulations state

!"Do not expose the unit to extreme temperatures. It should not be placed in direct sunlight or in a closed vehicle, neither should it be placed near heaters nor other heat sources. !"Do not store the unit in a humid or dusty place. !"Use a soft, dry cloth to clean the unit. Do not use a wet cloth or any solvent. !"Do not drop the unit or handle the unit carelessly. CAUTION: !"Never touch the pins of computer connection terminal. The internal circuits can be damaged by a static electricity disch

1.0 © Copyright 2000-2006 ACTiSYS Corporation All Rights Reserved ....: TABLE OF CONTENTS REVISION HISTORY...............................................................................................3 PRECAUTIONS........................................................................................................4 1. FEATURES................................................................................................................5 2. OVERVIEW............................................

Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 20. If your device is physically connected to COM2, highlight Communications ports(COM2), then click Next>. 21. Click Next>. 22. Click Finish Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS ME UNINSTALLATION GUIDE 1. Double click Sys SysSysControl Panel Control PanelControl Panel S SSy yys sst tttte eeeem mmmm icon on Cont

It is assumed that the user is familiar with the basic operation of Window 98/ME/2000/XP. PARTS CHECK LIST When you unpack the package, the following items should be found. 1. ACT-IR210L Adapter 2. 5 pins Motherboard Connector 3. User’s Guide 4. 5 pins to 6 pins changer SYSTEM REQUIREMENTS To use ACT-IR210L, your computer MUST meet the following requirements. 1. Window 98/ME/2000/XP. 2. Built in infrared I/O controller or super I/O chip on the motherboard with infrared connector available and do

Startup your computer system. 2. Click on Control Panel. 3. Double click System Icon. 4. Click on Hardware tab, then click Device Manager button. 5. Click on Infrared devices, then highlight ACTiSYS IR-220L+Serial Infrared Device. 6. Click Action and then Uninstall. Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. The device has been uninstalled and close device manager, restart your computer. Release 1.5 ACTiSYS Corporation 2001 All