Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 20. If your device is physically connected to COM2, highlight Communications ports(COM2), then click Next>. 21. Click Next>. 22. Click Finish Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS ME UNINSTALLATION GUIDE 1. Double click Sys SysSysControl Panel Control PanelControl Panel S SSy yys sst tttte eeeem mmmm icon on Control Panel Control Panel. 2. Go to Device Manager, highlight the items in the Infrared devices, then click Remove button. 3. Highlight the items in the Infrared devices, then click Remove button. 4. Highlight (Generic Infrared Serial Port or dongle), then click Remove button. Click OK button. 5. The device has been successfully uninstalled. Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS XP INSTALLATION GUIDE 1. Highlight My Computer, right click 2. Highlight Properties, left click 3. Click Add New Hardware Wizard. Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 4. Click Next. 5. Choose Yes, I have already…………….. then click Next>. 6. Wait processing Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Choose Add a new hardware device, then click Next>. 8. Choose install the hardware that I manuallyselect from a list (Advanced), then click Next. 9. Choose Infrared devices, then click Next> Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 10. Choose respective ACT model, then click Next> 11. Click Next> 12. Choose the Com port which the device physically connected, click Next> Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 13. Click Finish Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS XP UN-INSTALLATION GUIDE 1. Highlight My Computer, then right click. 2. Highlight Properties, then left click 3. Click Device Manager Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 4. Highlight the items under Infrared device, then right click. 5. Click Uninstall 6. Click OK, you have successfully uninstalled the device on your system. Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Click OK, you have successfully uninstalled the device on your system. Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR Dongle Installation Manual TROUBLE SHOOTING For help on general and miscellaneous problems you may be experiencing with your printing, refer to the following pages for possible solutions. Look up your problem and try the solution. SYMPTOM PROBLEM Solution Can not establish link (General) 1. The two IR devices are not aligned properly. 2. Distance is too near or far. 3. The device is inactivated. 4. The device is not installed properly 1. Properly align them again 2. Move one device to a proper distance. 3. Activate it by IR monitor. 4. Refer to Un-installation Guide to remove the device, then reinstall again. ACT-IR200L/220L+ is connected to and takes power only from the serial port of the notebook computer. The power-saving feature in the notebook computer either stops or reduces power output from the signal lines of the serial port to the ACT-IR200L/220L+ devices. 1. Set the “Power Management” control to “Advanced” or “Off” to enable power supplied from computer serial port to ACT-IR200L/220L+ devices. 2. Go to Integrate Peripheral to set the COM port to “Infrared”. 3. Do not install more than one infrared devices on one computer. File Transfer between IR-equipped PDA and ACT-IR device-attached host computer stops before finishing up and an error message appears. 1. The infrared communication is interfered. For example, something blocks out the infrared beam or the burst of string light source, etc. 2. Software does not support the IrDA controller chip on the motherboard. 3. Serial port is occupied and not available for IR transmission. 1. Check to find out the source of interference and eliminate it before trying again. 2. If you were restoring data, simply try again. 3. If you were doing backup something the PDA does not reset its flags and keeps stopping at the same position unless you press the RESET button once. Be very careful. DO NOT initialize (press ON key and RESET button at the same time) your PDA. Otherwise you may lose all your data. 4. Make proper model # selection in the software as specified in your PC system user`s manual. 5. Make sure to disconnect modem, etc. from the serial port to make it available for IR transmission. Release 1.5 ACTiSYS Corporation 2001 All Rights Reserved ACTiSYS Corp. Serial-IR ...
Эта инструкция также подходит к моделям:Компьютерные аксессуары - ACT-IR220L (504.9 kb)