Young children should be carefully supervised when they are in the same area as a hot termination. To prevent contact with hot surfaces, we recommend the use of a Termination Guard. See Page 33. This can be purchased at your local dealer. SV4.5 HT-2 Termination SV4.5 HT-2 Termination SV4.5 HT-2 Termination Horizontal terminations have been designed to perform in a wide range of weather conditions. Our terminations meet or exceed industry standards. When selecting the locations of your horizontal

Push the vent component against the collar until it fully engages, then twist the component clockwise,runningthe dimples downand along the incline channels until they seat at the end of the channels. The unitized design of the Secure Vent components will engage and seal both the inner and outer pipe elements with the same procedure. Sealant and securing screws are not required. Note: An elbow may also be attached to the appliance collar. Attach in the same manner as you would a vent section. E.

Une etiquette de securite doit etre collee sur la plaque de l’interrupteur controlant l’allumage du foyer (voirFigure A)ou sur le thermostat mural (voir Figure B) et, le cas echeant, sur le boitier de la telecommande (Figure C). Pour achever l’installation correcte de ce foyer, procedez comme suit avec les etiquettes adhesives en langues etrangeres fournies avec les instructions d’utilisation et d’entretien : 1. Reperez l’interrupteur ou le thermostat mural qui controle le foyer (verifiez que l’

A Notch Notch C Notches on bottom of log (C) fits over 2 locating brackets Top fork on log (B) fits into notch on log (A) B A 4 DA left log (B) 5 Top fork on log (D) fits into notch on log (A) Place Embers & Volcanic Stone as Shown 1 Volcanic Stone Embers Locating Brackets Notch for top right log (D) Notch for top The 2 notches on the bottom of log (A) rest on the locating brackets Sub-Floor Sub-Floor Flange Bottom Fork of log (D) rests on Sub-Floor Flange Bottom of log (B) rests on Sub-Floor MO

. Place the center log (C) as shown. The 2 notches on the bottom of log (C) fit over the corresponding locating brackets. 4. Place the left log (B) as shown. The top fork on log (B) fits into the notch on log (A). The bottom of log (B) rests on the subfloor. 5. Place the top right log (D) as shown. The top fork on log (D) fits into notch on log (A) as shown. The bottom fork on log (D) rests on subfloor flange (identified in photo #1). SSBV-4035 -Install as Follows Carefully position the ceramic

3. Locate the two (2) latches at the top of the control compartment. To disengage the two latches from the bottom vee-flange of the glass enclosure panel, reach for the handles located towards the back of the latches and pull the handles down toward the front of the appliance. 4. Swing the bottom of the door out and raise it slightly to lift the top flange of the door frame away from the appliance. Installing Glass Enclosure Panel (see Figure 11 ) 1. Visually inspect the gasket on the backside o

Order P/N 725,034CF. Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numero de la piece 725,034CF. US WARNINGS • Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will retain heat for a while after shutting off the appliance. Severe burns may result. • Carefully supervise children in the same room as appliance. • If small children are present in the home, it is recommended that this appliance be fitted with a screen

Homeowner must contact a qualified service technician at once if any abnormal condition is observed. If the venting system is disassembled for any reason, a qualified service technician should follow vent installation instructions for proper reassembly and proper sealing of the venting system components. However, more frequent periodic inspections and cleanings should be performed by the homeowner. Cleaning Glass (Also see Front Glass Enclosure Panel, Removal and Installation on Page 11). Note:

•Ensure front glass panel are in place and sealed during adjustment. CAUTIONS • Carbon will be produced if the air shutter is closed too much. Any damage due to carboning resulting from improperly setting the air shutter is not covered under the warranty. • Theairshutterdoorandnearby appliance surfaces are hot. Exercise caution to avoid injury while adjusting flame appearance. 1. Locate adjustment rod and adjust air shutter to the standard setting as shown in Figure 15 (adjustment rod is located

.Read Important Safety Information on page 4. All parts of your Lennox Hearth Products fireplace get EXTREMELY HOT! 3 .Afin d'eviter de vous bruler gravement ou de vous blesser, installez une grille ou une barriere physique pour empecher tout contact direct avec la vitre. Pour commander un PANNEAU DE PROTECTION Lennox® GRATUIT pour votre foyer, consultez les details dans la partie gauche. .Suivez les instructions de securite ci-dessous et veillez a ce que tous les membres de votre famille soient