3) Do not put your hands under the unit when the unit is required to be moved. 4) When the unit is not in use for a long period of time, please unplug the unit from the outlet. 5) After unplugging the unit, wait at least 10 minutes before re-plugging it. Failure to do so could cause damage to the compressor. 1) To minimize shock and fire hazards, please do not plug or unplug the cord with wet hands. 2) During maintenance and cleaning, please unplug the unit. 1) To minimize shock and fire hazards
CLEANING THE FAN BLADES AND MOTOR If necessary, clean the fan blades and motor with a soft cloth. If it is necessary to wash the fan blades, cover the fan motor to prevent moisture damage. CLEANING THE INTERIOR OF UNIT When cleaning the cabinet interior, use a solvent of warm water and mild soap. Do not use steel wool, caustic soap, abrasive cleaners, or bleach that may damage the stainless steel surface. Wash door gaskets on a regular basis, preferably weekly. Simply remove door gasket from the
............................................................Maintenance Page 6, 7............................................................................Troubleshooting Page 8........................................................................Important Information INSTALLATION/ OPERATION IMPORTANT!!! PLEASE READ BEFORE INSTALLATION 1) If the unit has recently been transported please let unit stand still for a minimum of 24 hours before plugging it in. 2) Make sure that the unit drops dow
To decrease the temperature (colder), turn clockwise. To increase the temperature (warmer), turn counter-clockwise - see diagram LOADING PRODUCT Shelves have been factory-installed for your convenience. Before loading shelves, please be sure that all shelf clips are completely fastened in their correct locations. It is important that all shelves rest completely level before stocking your cabinet with product. In order to maintain correct air flow inside the unit, please be sure to leave two to f
Plug in power cord. Thermostat set too high. Set thermostat to lower temperature. Cabinet in defrost cycle. Wait for defrost cycle to finish. Condensing unit runs for Excessive amount of warm product Allow adequate time for long periods of time. placed in cabinet. product to cool down. Prolonged door opening or door ajar. Ensure doors are closed when not in use. Avoid opening doors for long periods of time. Door gasket(s) not sealing properly. Ensure gaskets are snapped in completely. Remove gas
Lack of maintenance or misuse of the unit will VOID warranty. Please fill out the registration card and send it to the factory. CABINET LOCATION GUIDELINES 1) Install the unit on strong and leveled surfaces -unit may make unpleasant noises if surface is uneven -unit may malfunction if surface is uneven 2) Install the unit in an indoor, well-ventilated area -unit performs more efficiently in a well-ventilated area -for best performance, please maintain clearance of 4" on the back of the unit -out
............................................................Maintenance Page 7......................................................Temperature Control Instructions Page 9.........................................................................Refrigerator Settings Page 10..............................................................................Freezer Settings Page 11...............................................................................Troubleshooting LIMITED WARRANTY Jimex Corp. w
= minutes max = maximum hr. = hours N/A = not applicable Warning: Do not change the default settings of your ColdTech unit without consulting a qualified service technician or theColdTech service department. -9 Applicable to Models: CFD-1F, CFD-2F, CFD-3F ColdTech® Freezer Settings Temperature set to -4 F Parameter Function Set Range Default E1 Lower Setpoint Limit -40 F ~ set temp -10 F E2 Higher Setpoint Limit set temp ~ 120 F 20 F E3 Hysteresis, temp variance 1 ~ 18 F 10 F E4 Comp. start dela
Please read the manual thoroughly prior to equipment set-up, operation and maintenance. Failure to comply with regular maintenance guidelines outlined in this manual may void warranty. MUST READ!!! 1575 Zephyr Avenue Hayward, CA 94544 (800) 314-4477 (510) 477-3400 f: (510) 477-3413 TABLE OF CONTENTS Page 2...............................................................ColdTech Limited Warranty Page 3.........................................................................................Installat