Painted surfaces should be scraped or sanded clean to expose the bare metal before the ground lug is bolted or screwed down. Cover the bare metal area with paint or grease after you finish mounting the ground wire to prevent rust. REMOTE TURra Ora WIRE (NOS8A only) The ORANGE wire coming out of the NOS8A subwoofer's nozzle is the Remote Turn On Wire. This wire must be connected to 12 volts switched output from the radio or an accessory wire. irapuT wiRiraG (raOS8A only) Connect the low-level

Mounting the unit ensures that it will give you years of troublefree performance, and also guarantees that your unit is correctly oriented for it to operate properly. To begin, mount the bases parallel on the floor ofthe vehicle with the bases EXACLTY 13 inches apart, from inside edge to inside edge. Mounting these brackets incorrectly will make the final mounting steps difficult or impossible. The tall bracket should be mounted towards the front of the vehicle, to stand the back of the unit up,

Incorrect placement of the brackets will make final mounting difficult or impossible (See mounting on page 8). 5.) The bracket mounting bases should be screwed securely to a rigid surface that is part of, or anchored to, the structure of the vehicle. Be sure that your application meets all of these requirements before you continue the installation procedure! 4 FINISHING THE LOOK (Step 1) In order to complete the look of your subwoofer, you will need to install the included wire loom over th

Please use common sense and practice SAFE LISTENING ! If you have any questions contact the SAS Technical Support Department at: Phone - 800 THE-TUBE * Fax - (225) 272-9844 Email - tech@bazooka.com * Website - In Canada: (604) 988 2966 15049 Florida Blvd., Baton Rouge, LA. 70819 2 SYSTEM FEATURES • 6" or 8" PURE-PISTON WOOFER • 150 WATT HIGH POWER AMP (NOS8A ONLY) • TURBO COOLED VOICE COILS • BASS REFLEX, DUCTED PORT ENCLOSURE • CORNER LOADING • COPLANAR OUTPUT • HIGH OUTPUT EFFICIENC

Use provided screws to tighten down the amplifier. 5 POWER BASS BOOST BASS BOOST 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE CH1 CH2 CH3 CH4 MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI CAR BATTERY +12V + - POWER CONNECTIONS SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A 20A AUX 7.5A 20A AMP GND IN-LINE POWER FUSE MOUNTED WITHIN 12" FROM BATTERY RECOMMENDED (NOT PROVIDED) 94.7 RADIO'S REMOTE TURN-ON OUTPUT Connect the amplifier to the car's

Short Circuit Protectio. The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operation, correct the problem and turn the head unit off, then back on. The amplifier will reset and play again. Thermal Protectio. To protect the amplifier circuitry against damage caused by prolonged exposure to high temperatures, a thermal protection circuit is

Baton Rouge, LA. 70819 • 1-800-THE-TUBE www.bazooka.com

600W 65W x 4 85W x 4 175W x 2 20Hz-22KHz >90dB .03% 200mV-6V 1.0V-10.0V 10.5VDC-15.0VDC HP/FULL/LP HP/FULL/LP 60Hz-400Hz 12dB/Oct 0-12dB @ 45Hz Yes Yes 7.5A 3 x 20A 1 15 12 /” x 10 /” x 2 /” 2 48 * Low-pass Only ** Marine version of the ELA1500 and ELA 460, additional features include: Stainless Steel screws, aluminum end plates, marine coated circuit board, gold plated connectors, salt, fog and UV tested. Due to continuing product improvement, specifications subject to change without notice. 16

You should be able to use about 3/4 volume before the system gets loud but not distorting. It is very important when making these adjustments that you do not over drive the speakers (at point of distortion) this will cause permanent damage to the speakers. If you are unable to achieve 3/4 volume before distortion you will need to adjust gain control (in this case you would reduce the gain). The gain controls should be adjusted very slowly. It may help to have another person to assist you by adju

SPEAKER CONNECTIONS (TRI-MODE) NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D 100 F - + 100 F + - - 4 mH Left Mid / Tweeter 4 Ohm (2 Ohm Minimum) Mono Woofer 8 Ohm (4 Ohm Minimum) Right Mid / Tweeter 4 Ohm (2 Ohm Minimum) 12 The amplifier is capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crosso