Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Use provided screws to tighten down the amplifier. 5 POWER BASS BOOST BASS BOOST 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE CH1 CH2 CH3 CH4 MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI CAR BATTERY +12V + - POWER CONNECTIONS SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A 20A AUX 7.5A 20A AMP GND IN-LINE POWER FUSE MOUNTED WITHIN 12" FROM BATTERY RECOMMENDED (NOT PROVIDED) 94.7 RADIO'S REMOTE TURN-ON OUTPUT Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using an 4 to 8 gauge power wire for your connections depending on the amplifier and length of the wire. Strip one end of the wire to connect to the terminal on the amplifier marked +12V. Loosen screw terminal and connect bare wire and tighten. Use caution to make sure no stray wire stands come in contact with surrounding terminals causing short circuits. Run the wire directly to the positive terminal of the car's battery. Make sure to use an in-line fuse within 12” of the car's battery to protect the electrical system and amplifier against short circuits and/or power surges. Connect the ground terminal of the amplifier to the car's chassis. For the ground connection, use an 4 to 8 gauge wire (black) to connect to the terminal marked GND and then connect it to the car's chassis. Try to keep the length of the cable as short as possible, preferably less than 6". Also make sure that the point on the car where the connection is to be made is free of paint and dirt. Connect the remote terminal of the amplifier to a switchable +12V source. This connection allows the amplifier to be turned on and off with the power control of the radio. If the radio has a REMOTE output terminal, connect it to the amplifier's terminal marked REMOTE (using a 16 gauge wire or heavier). Now when the radio is turned on, the amplifier will automatically turn on. This connection can also be made to the radio’s Power Antenna wire. IMPORTANT! Before making any connections, disconnect the car’s battery until the installation is completed to avoid possible damage to the electrical system. 6 BASS POWER BOOST 0dB 12dB X-OVER 60Hz 400Hz LEVEL HI INPUT INPUT REMOTE R L MIN MAX FILTER LOW FLAT HI ELA150.1, ELA300.1 AND ELA / MAA500.1 SIGNAL CONNECTIONS R L POWER BASS BOOST BASS BOOST 0dB 12dB 0dB 12dB X-OVER X-OVER 60Hz 400Hz 60Hz 400Hz LEVEL INPUT HI INPUT HI INPUT REMOTE CH1 CH2 CH3 CH4 MIN MAX LEVEL MIN MAX FILTER LOW FLAT HI FILTER LOW FLAT HI 7 SIGNAL CONNECTIONS ELA / MAA60.4 SIGNAL CONNECTIONS FRONT REAR L R R L ELA60.2, and ELA100.2 SIGNAL CONNECTIONS Connect the RCA output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). Please note that when making these connections the signal inputs correspond with the speaker outputs. For example: If you connect the radios front right RCA to “CH 1” .......then speaker output “CH 1” will operate the front right speaker. POWER 0dB X-OVER 40Hz 130Hz REMOTE OUTPUT INPUT LEVEL L R MIN MAX L R Optional full range line out connection to additional amplifiers in the system. R L BASS POWER BOOST 0dB 12dB X-OVER 60Hz 400Hz LEVEL HI INPUT INPUT REMOTE R L MIN MAX FILTER LOW FLAT HI BASS POWER BOOST 0dB 12dB X-OVER 60Hz 400Hz LEVEL HI INPUT INPUT REMOTE R L MIN MAX F...
Эта инструкция также подходит к моделям:Автомагнитолы - ELA150.1 (4.25 mb)
Автомагнитолы - MAA500.1 (4.25 mb)
Автомагнитолы - ELA300.1 (4.25 mb)
Автомагнитолы - ELA500.1 (4.25 mb)