Remove the Model 3500 / 3700HD / 3000HD from its box and place it on a firm surface. 2. Plug unit into an outlet. 3. Locate key packaged with the unit. Unlock and remove the top cover of the unit. Locate the programming buttons that are labeled SELECT, UP, and DOWN. Place your key in a safe place for future access. 4. STEP 2 – PROGRAMMING THE MODEL 3500 / 3700HD / 3000HD Programming the Model 3500 / 3700HD / 3000HD is extremely easy and can be done in less than 5 minutes. STEP 3 – READY TO GO Re

The manufacturer reserves the right to determine whether the parts failed because of defective material, workmanship, or other causes. Failure caused by accident, alteration, misuse, or improper packaging of returned unit is not covered by this warranty. Any repair to the equipment other than by Pyramid voids the warranty. Users in countries other than the USA should contact the Dealer from whom the unit was purchased. The rights under this warranty are limited to the original user and may not b

DATE TIME – Prints current date and time. 2. DATE YR TIME – Prints current date, year, and time (small font). 3. DATE YR APPD – Prints current date, year, and APPD (approved) message. 4. DATE YR FAXD – Prints current date, year, and FAXD (faxed) message. 5. DATE YR FILE – Prints current date, year, and FILE (filed) message. 6. DATE YR IN – Prints current date, year, and IN message. 7. DATE YR OUT – Prints current date, year, and OUT message. 8. DATE YR PAID – Prints current date, year, and PAID

2. 5 MIN – This is the “5 minute rule”. With this option, the clock in/out and running totals will be rounded to the nearest 5-minute mark and will round “forward” at 2 minutes before the 5-minute mark and will round “back” up to 3 minutes after every 5-minute mark. 3. 10 MIN – This is the “10 minute rule”. With this option, the clock in/out and running totals will be rounded to the nearest 10 minute mark and will round “forward” at 5 minutes before the 10 minute mark and will round “back” up to

The 4000/4000HD uses bar-coded time cards (item #44100-10) that are pre- numbered 1 to 100. For each pay period an individual is assigned one pre-numbered (located in the upper right hand corner) time card. New time cards must be issued after every pay period. Note: Do not use duplicate time card numbers during a given pay period. In addition, use only Rev. D or greater time cards (noted at the bottom of each time card). Store your time cards in a dry area. Do not bend or soil the time cards. A

The master clock can handle a total of 300 events. An easy to use, plug and play system requires minimal set up time. The bell ringer is available in both 24 VDC and 0-220 VAC format. A one year manufacturer's warranty Pyramid technologies Major Accessories Features is included. Automatic time correction within 2 minutes if power was to fail Automatic Daylight Savings Time adjustment 12 hour or 24 hour display for digital clocks Battery back-up Easy installation Low voltage 24 VDC bel

LED LEVEL DISPLAY 2. POWER ON/OFF 5. EQUALIZER CONTROL 3. TONE DEFEAT 2 SPECIFICATIONS Input Impedance............ Control Frequencies.......... Control Range.............. Frequency Response.......... Signal to Noise.............. Input Sensitivity for 400mV Output Power Requirement .......... Size..................... 100 Ohm low, 10K Ohm high. 60, 150, 400, 1K, 2.4K, 6K, 15KHz. ± 12dB boost or cut. 20~20KHz. Better than 85 dB (A—Wtd) 2.0 volts low impedance. 200mV high imped

Depressing the tone defeat button again to "OFF" brings the equalizer into operation. 3. FADER CONTROL A) DUAL AMPLIFIER 4-SPEAKER SYSTEM Rotating the knob to the FRONT side brings up the level of the FRONT speakers. Rotating to the REAR side brings up the level of the REAR speakers. At mid position, both sets of speakers are at maximum level. B) 2-SPEAKER SYSTEM The fader control knob should be turned to the end position which provides the loudest sound for using both sets of speakers. 4

number • also include a check or money order for $15.00 for return handling, and insurance, or provide your number with expiration date. Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid. This warranty will be considered void if the unit was tampered with, improperly serviced, or subject to misuse, neglect, or accidental damage. All Pyramid products are carefully constructed and thoroughly tested before shipment. Pr

To prevent this, connect one end of a shield wire to the amplifier's ground screw (on rear panel). Then connect the other end of this wire to the ground terminal on the mixer or preamplifier enclosure. PREAMP OR MIXER Input connections These amplifiers accept a board range of input sources, including Compact Disc (CD,DVD) Cassette, Reel· to· Reel or other tape players; Tuners; Equalizers; Signal Processors. Connecting a CD, DVD, tape player or tuner In a normal installation, one would use the RC