If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If plug does not fit fully into the wall outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord re

961 95 00-01 22 18 21 53 19 28 19 55 28 19 55 54 54 6 6 5 6 6 9 12 7 7 8 6 11 27 27 30 26 25 20 23 24 31 25 24 26 23 29 21 53 19 20 18 10 4 13 14 16 15 36 37 50 47 42 44 27 43 46 38 45 4327 41 42 40 39 34 32 49 19 48 51 33 35 56 REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 10530SBE (96195000101), PRODUCT NO. 961 95 00-01 KEY PART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley, Impeller 532 18 89-09 Bearing Assembly, Flange 6 532 15 53-77 Nut, Hex Flange 5/16-18 7 532 18 03-

If the chain is too loose, it will sag below the bar. tGuideBarChainAdjustmenBar Nuts Adjusting Tool (Bar Tool) Screw Adjusting the tension: Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time before you start the chain saw. 1. Loosen bar nuts until they are finger tight against the clutch cover. 2. Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Included with this saw is a 3.2 ounce (95 ml) container of Poulan/WEED EATER brand synthetic oil. Pour the entire contents of this container into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture. DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION. CAUTION: Never use straight gasoline in your unit. This will cause

CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. NOTE: It is normal for a small amount of oil to appear under the saw after engine stops. Do not confuse this with a leaking oil tank. S ON/STOP Switch - --Ensure ON/STOP switch functions properly by moving the switch to the STOP position. Make sure engine stops; then restart engine and continue. S Fuel Tank - --Do not use saw if fuel tank shows signs of damage or leaks. S Oil Tank - --D

STARTING A WARM ENGINE Pull starter rope sharply while squeezing throttle trigger until engine runs. NOTE: Normally, the warm starting procedure can be used within 5- --10 minutes after the unit is turned off. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit. STARTING A FLOODED ENGINE Move the start lever to the RUN position and full

Wearing safety leg guards is recommended. S Always wear foot protection. Do not go barefoot or wear sandals. S Secure hair above shoulder length. Secure or remove loose clothing and jewelry or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts. S Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line/blade. S Stay Alert. Do not operate unit when you are tired, ill, upset or under influence of alcohol, 4

Veuillez ne pas retourner le produit au detaillant. 1- --800- --554- --6723 Register your product online at: Registre su producto en linea en: Enregistrez votre produit en ligne a l’adresse : Instruction Manual Manual de Instrucciones Manuel d’Instructions 1420 1630 WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e instrucciones

CARTON CONTENTS S Chain Saw (fully assembled) S Bar Sheath Examine parts for damage. Do not use damaged parts. NOTE: If youneed assistanceor find that parts are missing or damaged, please call 1-800-554-6723. ASSEMBLY Your unit is fully assembled; no assembly is required. 6 OPERATIONOPERATION KNOW YOUR SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and ad

Removebarclamp. DriveSprocket Bar Knob Bar Clamp 8. Pull guide bar forward until the chain CHAIN ADJUSTMENT is snug in the guide bar groove. Ensure all drive links are in the bar groove. 9. Install bar clamp. Be sure adjusting pin is in the adjusting pin hole in the guide bar. CAUTION: It is very important when installing the bar clamp that the adjusting pin aligns into the adjusting pin hole in the bar. Failure to install the bar clamp correctly may result in permanent damage to your chain saw.