Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, norme NFPA 51B, de la National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269.9101 (telephone : (617) 770.3000, site Web : et OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and Part 1926, Subpart J, de l’U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 152

. . . . 134201 . . STAND-OFF SUPPORT, pc card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ... 10. . . . . . . . . . . . . . . . . . . 162821 . . BRACKET, mtg LEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ... 11 . . . . . . . HD1 . . . . . . 148417 . . TRANSDUCER, current 1000A module. . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . PLG14 . . . . . 130204 . . HOUSING PLUG PINS & SKTS . . . . . . . . . . . . . . . . . . . .

Selecting a Location loc_2 3/96 - Ref. 151 556 / 802 183 1 Lifting Handles Use handles to lift unit. 2 Hand Cart Use cart or similar device to move unit. 3 Line Disconnect Device Locate unit near correct input power supply. Special installation may be required where gasoline or volatile liquids are present . see NEC Article 511 or CEC Section 20. 24 in (610 mm) 17 in (432 mm) 12-1/2 in (318 mm) Movement 2 Do not move or operate unit where it could tip. Location 3 Dimensions And Weight 18 in (

. . . . . . . . . . . . . . . . . . . . . . . . . . 12 SECTION 5 . OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5-1. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5-2. Cutting Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

M/6.5 Wire Feeder with Remote Control SuitCase™ 8RC and 12RC Processes MIG (GMAW) Flux Cored (FCAW) Input Power 24 VAC, 7 A/10 A Weight 8RC: 22.0 lb (9.9 kg) 12RC: 25.5 lb (11.6 kg) Industrial Applications Shipbuilding Construction Heavy Manufacturing Rental Quick Specs Remote voltage control — standard. Updated front panels! Improved trigger strain relief! The Power of Blue®. Standard gas solenoid controlling gas flow. Totally enclosed, impact- resistant, flame-retardant case provides strength

804 001-B Installing Wire Guide And Drive Rolls: 1 Drive Roll Nut 2 Drive Roll Carrier Turn nut one click until lobes of nut line up with lobes of drive roll carrier. 3 Drive Roll Slide drive roll onto drive roll carrier. Turn nut one click. Repeat procedure for top drive roll. 4 Inlet Wire Guide Screw 5 Inlet Wire Guide (One Piece Anti-wear) The factory installed inlet wire guide is good for up to 5/64 inch diameter wire. Loosen securing screw. Align inlet guide so inlet guide screw is centere

DC/27.2 TIG/Stick Welding Power Source Maxstar® 150 STH Processes TIG (GTAW) Pulsed TIG (GTAW-P) Stick (SMAW) Input Power 1-Phase Power Amperage Range 115 VAC: 5 – 150 A (DC TIG) 20 – 100 A (DC Stick) 230 VAC: 5 – 150 A (DC TIG) 20 – 150 A (DC Stick) Max. Open-Circuit Voltage 90 Weight 13.7 lb (6.2 kg) Light Industrial Applications Process Pipe Dairy Industry Food/Beverage Industry Restaurant/Kitchen Repair Experimental Aircraft Shipboard Installation/Repair Maintenance Repair Quick Specs Improv

9 Contact Tip Thread wire through canister inlet guide, along drive roll groove, and out contact tip. Install spool so wire feeds off bottom. 10 Spool Brake Thumbnut If necessary, turn thumbnut counterclockwise slightly to install spool. 11 Thumbscrew (Canister Rotation) Loosen thumbscrew to rotate canister (see Section 4-4). Close and secure pressure roll assembly. Reinstall top cover and canister cover. Tools Needed: 9 1 2 10 3 4 5 6 8 7 11 4-4. Rotating Canister 150 433-A 1 Canister Loosen ca

Volt-Ampere Curves The volt-ampere curves show the minimum and maximum voltage and amperage output capabilities of the welding power source. Curves of other settings fall between the curves shown. ssb1.1 10/91 – SB-187 997 OM-1318 Page 9 OM-1318 Page 10 2-3. Welding Power Source Duty Cycle And Overheating Duty Cycle is percentage of 10 minutes that unit can weld at rated load without overheating. If unit overheats, thermostat(s) opens, output stops, and cooling fan runs. Wait fifteen minutes for

1 Spectrum Lynx 2 Power Plug 3 Engine-Driven Welding Generator With Required Receptacle Installed 4 AC Power Receptacle For Lynx Connect power plug to proper receptacle on engine-driven welding generator. 1 801 977-A / Ref. ST-802 200 Rear of Unit 2 3 4 Example Welding Generator OM-2219 Page 12 SECTION 3 – OPERATION If the welding generator includes a fine adjust control, be sure to set the control to maximum for full output control capacity. When using the Lynx, auxiliary power output is not av