(Picture 10) 5. Lock the gear shaft by putting a pin provided or screwdriver through the aligned keyholes in the gear case cover and the gear case. Use a socket wrench to tighten the blade-mounting bolt. Rotate bolt counter clockwise to tighten. (Picture 11) 6. Split the bracket, install the wheel assembly to the tube, and clamp it at the position best for your job, using two screws. (Picture 12 and 13) 7. You can replace loop handle with the U-shaped handle that comes with your Edge Trimmer Att

The thatch can soon be so dense as to prevent water, nutrients and oxygen penetrating the lawn’s root system, resistance to wear and new growth subsequently weaken. Disease and drought resistance is reduced with weeds and moss becoming dominant. Scarification not only removes harmful thatch, it also reduces the amount of moss and weeds. In addition the compacted soil surface is loosened thus enabling it to breathe and absorb water, oxygen and nutrients. Due to the thinning out achieved by scar

inches 1 inch = 25.4 mm 25 26 REPAIR PARTS DRIVE SNOW THROWER - - MODEL NO. 1027STE (HL1027STEA), PRODUCT NO. 954 63 35-45 35 33 15 41 22 34 29 22 31 26 7 2 43 2 11 3 3 25 24 23 12 32 27 44 20 21 21 22 16 17 1 15 2 1 4 13 4 2 1 5 3 2 4 5 3 3 5 1 2 3 13 1 5 2 7 8 9 10 6 3 3 41 14 2 19 18 28 30 40 39 38 36 37 33 REPAIR PARTS DRIVE SNOW THROWER - - MODEL NO. 1027STE (HL1027STEA), PRODUCT NO. 954 63 35-45 KEY PART NO. NO. DESCRIPTION 1 532 14 63-15 Screw, Hex Head 5/16-18 x 3/4 2 873 80 05-00 Nut, L

CHOKE ENGINE OIL GAS O LINE CONTROL FILL CAP / DIPSTICK FILLER CAP NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT. 12 FIG. 20 OPERATION TO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current. • Be sure your house is a 120 Volt A.C. three-wire groun

4. Connect spark plug wire to spark plug. IMPELLER SHEAR BOLTS The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are de signed to break, preventing damage to any other compo nents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts: AUGER SHAFT 1/4-20 x 2 SHOULDER / SHEAR BOLT 1/4-20 LOC

NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3 532 17 86-74 Control Assembly, Defl ector 4 873 80 06-00 Nut, Lock 3/8-16 5 819 13 13-16 Washer, Flat 3/8 6 532 17 86-59 Control Assembly, Chute Rotater 7 532 18 40-89 Support, Pivot 8 532 15 00-78 Screw, Hex Head 5/16-18 x 3/4 9 532 18 45-05 Spring, Deflector 10 532 17 98-29 Bolt, Shoulder 11 532 17 92-46 Washer, Flat 1/4 12 873 80 04-00 Nut, Lock 1/4-20 13 872 25 05-05 Bolt, Carriage 5/16-18 14 873 80 05-00 Nut, Loc

12. Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse. 13. Disengage power to the collector/impeller when snow thrower is transported or not in use. 14. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs). 15. Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles.

To avoid possible freeze-up of the starter, proceed as follows: ELECTRIC STARTER 1. Connect the power cord to the engine. 2. Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle. 3. While the engine is running, push starter button and spin the starter for several seconds. NOTE: The unusual sound made while starter is spinning will not harm the engine or starter. 4. Disconnect the power cord from the receptacle first, then from the engine. RECOIL STARTER 1. Whi

Lubricate the clutch bearing with the same type of grease as used for the guide bar with nose wheel, i. e. ball bearing grease. Use the grease gun supplied with the kit of tools: Remove the clutch housing. Inject grease through the hole in the centre of the clutch. Two strokes of the grease gun will be sufficient. (Check that grease emerges from the gun when it is pumped.) Schmieren des Nadellagers in der Kupplungstrommel Das Kupplungslager mit Fett der gleichen Art wie die Schiene mit Umlenkrol

6. Never attempt to unclog the collection system until the mower’s engine engine has been shut off and all moving parts have come to a complete stop. 7. Do not stand behind the vent at the rear of the collection system due to the potential for small pieces of blowing debris to escape through the vent. 8. Wear eye and ear protection. 12 SERVICE AND MAINTENANCE Transport WARNING The collection system bags must be completely empty or removed while driving forward onto a trailer. If the mower must b