WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROvAL OF GRIzzLY INDUSTRIAL, INC. #TS11344 PRINTED IN TAIWAN

Davlumbaz Uzivatelska Poirueka Odsavac par FDB 9078 SIL-K INDEX EN RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 3 CHARACTERISTICS ............................................................................................................................................................. 4 INSTALLATION.............................................................................................

14. Test for leakage. 5/7 General maintenance Clean aerator periodically. Do not use harsh detergents, solvents, chemical agents, metallic sponges, etc. that could harm the surface. Clean only with a soft sponge and soapy water. Clean and dry the faucet properly in case of hard water deposits which could damage the surface. Replacing the spray flex hose 1. Shut off the water supply to the faucet. 2. Pull the spout outwards from its place and unscrew the aerator . 3. Unscrew the hand shower from

(1-800-626-5771) or visit TABLE OF CONTENT 1 Faucet 2 Flexible hose of the side spray 3 Hook for side spray 4 Side spray 5 Priority water flow system 6 Fastening set (rubber washer, metal washer, nut) 7 Fastening set (rubber washer, triangular flange, metal washer, nut, allen key 2,5mm) 8 Counter weight 3 ENGLISH Install faucet to the sink or countertop Set the faucet into place on the sink as indicated in the figure. NOTE: the rubber O-ring should be sitting on top of the count

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-1600 Series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Inlet connections: 1/2. NPSM Please read our instruction before you

Remove all contents from the package and check for completeness (see itemized table and picture). NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit TABLE OF CONTENT 1 Faucet 2 Spray head 3 Counter weight and gaskets 4 Fastening set (rubber washer, triangular flange, metal washer, threaded nut) 5 Hexagonal wrench 6 Valve-holder 2/8 2. Remove all mounting hardware from protective plastic bag. 3. Place the large O-ring over the faucet shank and place the faucet into th

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-3000 series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Tailpipe connections: 3/8. O.D. Please read our instruction before

FFP S700 SERIES Pull-Out Spray Faucet Installation guide ENGLISH 2 G 1748.XX G 1782 G 1156 G 29016 G R0239.XX G 13396.XX G R0637 G R1664 G 1636 G 1463 TECHNICAL DATA · Minimum working pressure 0,5 bar · Maximum working pressure 5 bar · Recommended working pressure 3 bar (in case of water pressure higher than 5 bar it is recommended to install pressure reducers) · Maximum working temperature 70°C PARTS LIST G 13396.XX Handle G R0239.XX Ring cap G 1156 Cartridge G R0637 Fastening set (rubber washe

NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit TABLE OF CONTENTS 1 Faucet 2 Wall fastening set 3 Wall flange (over the sink) 4 Wall flange (under the sink) 5 Fastening set (rubber washer, triangular flange, metal washer, nut) 6 Non-return valves 1 5 6 3 4 2 2. Remove all mounting hardware from protecting plastic bag. 3. Place the large O-ring over the faucet shank and place the faucet into the desired location. NOTE: the rubber O-ring should be sitting on top of

These include pre-filter and carbon cartridges. Filter cartridges are easily replaced by removing the stainless steel cartridge housing’s cap. This automatically shuts off the water supply and allows the new cartridge to be inserted quickly and cleanly. It is recommended that a new cartridge is used every 6-12 months according to water quality. Any noticeable reduction in the filtered water’s flow rate usually indicates a new cartridge is required. Franke Uniftow and Little Butler™ Systems wor