Your Drolet insert will attain its best performance if installed with a chimney that generates its own draft. The minimum requirement of a flue will be the installation of a flue connector (the liner must conform to UL1777 chimney liners) from the insert into the first flue tile of the chimney (USA), see Figure 2.3 , or a continuous stainless steel liner (the liner must conform to the Class 3 requirements of CAN/ULC-S635) directly connected to the flue outlet (Canada), see Figure 2.2. A continuo

SBI reserves itself the right to modify its products without any obligation on its part. Il est possible que certains changements aient été apportés aux produits après la publication de cette brochure. SBI se réserve le droit de modifier ses produits en tout temps sans obligation de sa part. 773388995397

1700, Leon-Harmel, Quebec (Quebec) G1N 4R9 Tel : (418 ) 527-3060 Fax : (418 ) 527-4311 READ AND KEEP THIS MANUAL FOR REFERENCE INTRODUCTION Stove Builder International, one of the most important wood stove and fireplace manufacturers in North America, congratulates you on your purchase and wishes to help you get maximum satisfaction from your wood stove. In the pages that follow, we will give you advice on wood heating and controlled combustion as well as technical specifications regarding insta

OPEN WINDOWS 2. TURN OFF MAIN GAS SUPPLY 3. DON’T TOUCH ELECTRICAL SWITCHES 4. EXTINGUISH ANY OPEN FLAME 5. IMMEDIATELY CALL YOUR GAS SUPPLIER Tested by : WARNOCK HERSEY Manufactured by : DROLET STOVES & FIREPLACES INC. 1700, Leon-Harmel Quebec, Qc (Canada) G1N 4R9 Rev. 07/96 45028A TABLE OF CONTENTS : GENERAL INFORMATION :............................................................................. 2 WARNING :......................................................................................

An example of the energy values of some common wood fuels found in North America is given in the following table: Wood species Energy yield (millions of BTU/cord) High energy yield Oak 29 Sugar Maple 28 Beech 26 Yellow birch 25 Ash 24 Elm 23 Medium energy yield Larch (Tamarack) 23 Red Maple 23 Douglas red fir 23 Silver birch 22 Alder 18 Poplar 17 Hemlock 17 Low energy yield Spruce 17 Pine 17 Bass 16 Fir 13 High energy yield Oak 29 Sugar Maple 28 Beech 26 Yellow birch 25 Ash 24 Elm 23 Medium ener

Round chimneys are the most efficient. The interior diameter of the chimney should be identical to the stove's smoke exhaust. A chimney which is too small may cause draft problems, since it may not have the required volume to properly evacuate the quantity of smoke resulting from the combustion. A chimney which is too large may also cause draft problems. In fact, a large chimney will be harder to warm-up and may not reach high enough temperatures to create a proper draft effect. Note that it is

ASH DISPOSAL Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is cold, such as in the morning. Always dispose of ashes in a metal container with a tight fitting lid. Place this container on a non combustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the close container

5. Turn the gas valve knob to the “ON” position. 6. Turn the face place mounted switch to the “ON” position. If you don’t have an additional wall switch , the main burner will come on. Otherwise, turn the wall switch to “ON” if you want the main burner to come on. 7. The other knob controls the gas flow and the power of the appliance. SHUTDOWN INSTRUCTIONS Main burner only : Turn off the face plate switch ( or wall switch ). To relight the main burner, turn the switch on ( or the wall switch ) P

A wood stove must never be installed in a hallway or near a staircase, since it may block the way in case of fire or fall to respect required clearances. FLOOR PROTECTOR Your wood stove should be placed on a non-combustible surface. The floor protector should be under the stove, eighteen inches beyond the front and eight inches beyond each side of the fuel loading and ash removal opening. If there is a horizontal section of chimney connector, the floor protector should go under it and two inches

Follow the same assembly steps. Certains ventilateurs ou panneaux peuvent différer de ceux montrés sur le graphique. Suivre les mêmes instructions d'insîaliatioo. Step 1 The blower assembly must be disconnected from the SOURCE OF ELECTRICAL SUPPLY BEFORE ATTEMPTING THE INSTALLATION. With pliers, cut the 6 microjoints and remove panel Note: Discard the panel. Étape 1 Le ventilateur doit être débranché de la source de COURANT AVANT DE PROCÉDER À L'INSTALLATION. Couper à l’aide de pinces