14-651 14-651 Hollow Chisel Mortiser Mortaiseuse a bedane creux Mortajadora de cincel hueco Instruction Manual Manuel d’utilisation Manual de instrucciones FRANCAIS (15) ESPANOL (27) (800) 223-7278 - US (800) 463-3582 - CANADA A19592 - 09-15-06 Copyright © 2006 Delta Machinery TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ....................2 SAFETY GUIDELINES - DEFINITIONS .....................3 GENERAL SAFETY RULES .......................................3 ADDITIONAL SPECOF

1. True Up One Face – Feed one face of the board through a jointer. Make thin cuts with each pass until the entire surface is flat. 2. Plane to Thickness – Place the surfaced side (STEP 1) face down and feed the board through a planer until the opposite side is flat. Plane both sides of the board until you achieve your desired thickness. Make thin cuts, alternating sides with each pass. If, during the planing operation, you notice the board twisting, warping or bowing, start again with STEP 1. 3

Tighten the screw. Adjust the blade guide bearings (C,G) by loosening the screw (E) and rotating the bearing on the shaft (F) so that the bearings touch, but do not pinch the blade. To gain access the back bearing (G), you will need to remove the table insert and tilt the table to the right. Return table to level position. The front edge of the guide bearings (C) should be just behind the “gullets” of the saw teeth. To adjust, loosen the hex screw (D) and slide the bearing assembly into place. T

Such preventive safety measures reduce the risk of starting the tool accidentally. 5. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 6. When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire. 7. Main

Suite 300, Richmond Hill, ON, L4B 1M4. Information en ce qui concerne l'operation sure et correcte de cet outil est disponible des sources suivantes: • Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 ou en ligne • National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201 • American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 -ANSI 01.1 Safety Requirements for Woodworking Machines • U.S. Department of Labor regulations MESURES DE

Always follow basic safety precautions to reduce the risk of personal injury. Improper operation, maintenance, or modification of tools or equipment could result in serious injury and property damage. Our tools and equipment are designed for certain applications. DO NOT modify and/or use this product for any application other than that for which it was designed. If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised

To remove the battery pack from the tool, depress release buttons (B) on both sides, remove the battery pack (C). Insert it into the charger as described in the charger manual. Important Charging Notes 1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage

Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. ESPANOL: PAGINA 17 FRANCAISE : PAGE 33 MODEL 340 Double Insulated Finishing Sander Type ___________________________________________ Serial No. _______________________________________ Copyright © 2005 Porter-Cable Part No. A

REVIEW SAFETY RULES AND OPERATING INSTRUCTIONS FREQUENTLY. This booklet is provided for your convenience: iw the use ami care of your new DeWalt Saw. These instructions include operation, usage, precautions^ preventive maintenance, maintenance and other pertinent data to assist you in assuring long; life and dependable service from your saw. 700 8" RADIAL ARM SAW No. 7700/3400,120 VOLT, TYPE 5 No. 7700-01,220 VOLT, TYPE 5 Bulletin No. 8814 - INDEX Unpacking, Set-Up..............2-4 Macfii

3. When making this adjustment, MAKE SURE THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE and lower the blade as far as possible. Rotate the blade by hand to make certain the teeth do not contact any metal surfaces and adjust if necessary. After adjustment is completed, tighten locknut (A) Fig. 29. A B C Fig. 29 13 1313 ADJUSTING BLADE GUARD After an extended period of time the movable blade guard (A) Fig. 30, might become sloppy and move erratically when the cuttinghead is lowered. This can b