Before shipment to your dealer, it was carefully inspected and put through a rigorous adjustment process by highly skilled technicians to ensure you the best possible sound and playability. This instrument is covered by Ampeg's Five Year Warranty. We urge you to take a few minutes to familiarize yourself with the terms of this warranty as well as some tips regarding the operation of your instrument. With reasonable care, your Ampeg Dan Armstrong Guitar should provide you with many years of play

11 Pre FX: (10 pre-effect+pedal-wah) Comp, Wah, Acoustic, Drone, P/U and more. 10 Modulation, Filter and Pitch effects. 10 Delay/Reverb effects • 80 Programs: 40 presets and 40 user • 58 total effect types, 6 FX can be used simultaneously. (3 effects blocks, Noise Reduction, Drive/Amp and Cabinet modeling) • Intuitive interface for quick and easy operation • Delay and Reverb Effects carry over when changing between programs with the same settings • Program select foot switches with large LED ind

Note: In this mode, if you press the Program Up (Value) switch, the current parameter value will be displayed. If you press the Program Down (Type/Param) switch, it will display to the currently selected FX type/parameter. S SSa aav vvi iin nng gg a aa P PPr rro oog ggr rra aam mm You’ve tweaked and turned some knobs, and you like the changes that you’ve made – now to save your program: 1. Set the Function Knob to the “WRITE” position, and press WRITE (“UP”) Button. A User program number will bl

Do not attempt to defeat the safety ground connection! 15. SPEAKERS: Use these jacks to connect the amplifier to your speaker(s) using high quality speaker cables terminated with 1/4” connectors. WARNING: The speaker output of this unit can exceed 10 Watts and could be a shock injury. Connection to speakers should be performed by a skilled person in compliance with local building codes. Class 2 wiring is required for speaker cables. Use of external speakers outside the ratings stated at the spea

9. LIMITER: The B2/B2R uses an internal Optocoupler Limiter to assist in keeping the power amplifier’s output “clean” at extreme volume levels. (All amplifiers begin to clip their output signals as they approach maximum output levels, resulting in distortion which may damage your speakers.) To engage the Limiter, depress the Limit switch. Whenever the amplifier is at full power, the adjacent LED will flash. This is an indication that the limiter is keeping peak signals from clipping the output.

5. BASS: This is the primary low frequency control which allows for 8dB of cut or boost at 50Hz. 6. ULTRA-MID: This is the primary midrange control. Rotate the control to the left of center for a “contoured” sound (more distant, less midrange output) or to the right of center for a pronounced (more upfront) tone. 7. TREBLE: This is the primary high frequency control which allows for 12dB of boost or 19dB of cut at 5kHz. 8. MASTER: Set the overall output level of the amplifier with this control.

INPUT: The signal output from an instrument (active or passive) or a line level signal may be connected here by means of a shielded instrument cable. 2. -15dB PAD: This switch, when depressed, attenuates the input signal by 15dB. Attenuation allows the Gain control (#4) to be used in a more usable (higher) position. If clipping is indicated with the Gain control at a low setting, attenuation is needed. 3. PEAK LED: This LED flashes when the signal level into the preamp approaches clipping. Adjus

INTERNE TEILE KONNEN NICHT VOM BENUTZER GEWARTET WERDEN. DIE WARTUNG IS QUALIFIZIERTEM WARTUNGSPERSONAL ZU UBERLASSEN. THIS EQUIPMENT HAS BEEN DESIGNED AND ENGINEERED TO PROVIDE SAFE AND RELIABLE OPERATION. IN ORDER TO PROLONG THE LIFE OF THE UNIT AND PREVENT ACCIDEN- TAL DAMAGES OR INJURY, PLEASE FOLLOW THESE PRECAUTIONARY GUIDELINES: WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN CHASSIS; DO NOT DEFEAT OR REMOVE THE GROUND PIN OF THE POWER CORD; CONNECT ONLY TO A PROP- ERLY GROUNDE

Attenuation allows the Gain control (#4) to be used in a more usable (higher) position. If clipping is indicated with the Gain control at a low setting, attenuation is needed. 3. PEAK LED: This LED flashes when the signal level into the preamp approaches clipping. Adjust the Gain control (#4) until a strong signal from your instrument causes this LED to flicker. NOTE: If the LED flashes frequently with the Gain at a low setting, use the -15dB pad (#2) to attenuate the input signal and readjust t

Each of the jacks may be used as an input or a through connection. The three position HF Horn switch allows for: • Full high frequency output (0 setting) • High frequencies reduced by 6dB (-6 setting) • Horn shutoff (off setting) IMPORTANT SAFETY INSTRUCTIONS: 1.Read, follow and keep these instructions. Heed all warnings. 2.This speaker is capable of producing high sound pressure levels that may cause permanent hearing damage. User caution is advised and ear protection is recommended duri