for CP43A2003) (3 Signals/Rev. for CP43D2001) Specifications Model No. Working Voltage (V) Rated Voltage (V) Max Water Head m-H.O Max Flow Rate ml/min Weight (gw) Operation Temperature Noise dB(A) MTBF (hour) CP43A2003 6-13 12.0 1.8 1750 50 5°C - 65°C 23 44,000at 35°C CP43D2001 6-13 12.0 1.7 1650 50 5°C - 60°C 25 30,000at 35°C *Noise Measurement Condition: 25 cm above Pump ( Pump is filled with Pure Water) * Model CP43D2001 is cost down solution. * All readings are typical values.

for CP43A2003) (3 Signals/Rev. for CP43D2001) Specifications Model No. Working Voltage (V) Rated Voltage (V) Max Water Head m-H.O Max Flow Rate ml/min Weight (gw) Operation Temperature Noise dB(A) MTBF (hour) CP43A2003 6-13 12.0 1.8 1750 50 5°C - 65°C 23 44,000at 35°C CP43D2001 6-13 12.0 1.7 1650 50 5°C - 60°C 25 30,000at 35°C *Noise Measurement Condition: 25 cm above Pump ( Pump is filled with Pure Water) * Model CP43D2001 is cost down solution. * All readings are typical values.

.. DANGER! Caution! Electric Shock! .. When the power is on, DO NOT touch the AC terminals in case an electric shock may occur. .. Make sure the power is disconnected when you check the unit inside. .. CTA series is an OPEN-TYPE device. They are intended for installation completely within an overall panel and are for use in counting or timing application. If it will cause serious injury to workers or damage on other equipments when used in a dangerous environment, please make sure it is installe

You will be prompted for a name and Disk location. ¦ Press < <<<<> >>>> or Tab to survey the subdirectory in which your file will be saved. Specify a different name from any of these to create a new file, or select one of the existing files (which will then be overwritten). Restoring a configuration ¦ In the SunData program on the Workabout, proceed to Menu, File, RestoreConfig'n. Press < <<<<> >>>> or Tab to survey the list, and then select the .cfg file that you want to restore. Data files A d

An AC motor drive can connect to multiple AC motor drives by using this communication board (1 to 4/8) to control multi-machine communication. Refer to the following diagrams for details. INPUT SG- SG+ OUT 1 6 5 4 3 2 1 OUT 2 OUT_3 OUT_4 VFD-CMD04 VFD-CMD08 AC POWER SUPPLY RS-232 PC 1-0 DVP PLC DATA- RS-485 ADDRESS 1 ~ 8 65432 1 OUT 1 OUT_2 OUT_3 OUT_4 65432 1 OUT 1 OUT 2 OUT_3 OUT_4 1 2 3 4 5 6 7 8 PC-^ PLC -► multi-machine communication board -► AC motor drives DA

Use the low speeds for normal use and the higher speeds for strong odors or fumes. Minimize cross drafts which will reduce the effectiveness of the hood. 8 Hood Cleaning Be sure lights are cool before cleaning the hood. To Clean Filters Figure 8 The metal grease filters will last forever. They are made of anodized aluminum It is recommended that the filters be washed at least once a month; they can be washed by hand or in the dishwasher. Drain water through edge holes and let each filt

-On ducted and non-ducted installations in rooms with 9-foot ceilings, the vents are exposed. Install the flue with air vents up. ROOMS WITH 10-FOOT CEILINGS (DUCTED HOODS ONLY) Rooms with 10-foot ceilings require flue extension model FXWC50EC available from your local dealer. Discard the upper flue supplied with the product. Replace it with the flue extension. 2. Raise the upper flue until its holes align with holes in the flue mounting bracket (located on ceiling). Fig. 15. 3. Secure the upper

This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. 10 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check