...................08 BASIC OPERATIONS POWER ON/OFF......................................................................................................................................................... 10 NAV................................................................. ............................................................................................................ 10 VOLUME ADJUSTMENT..............................................................................................

The demodulated 121.5 MHz audio signal is annunciated at all times. If there is not any signal on the 121.5 MHz carrier, whether activated beacon or other source, static will be audible. The speaker volume is high, and the signal strength meter is active. Monitor Low mode This mode is identical to the Monitor High mode except that the speaker volume is lower. NOTE: The ARX-50 reverts back to Alarm mode after 15 minutes in Monitor High mode. Training mode Operation in Training mode is identical t

The SM-2 has been designed and tested to pass the tough ANSI/UL 1196 and MSC.81(70) requirements. 3.2 Purpose This unit is a portable electronic floating strobe light which automatically rights itself and begins flashing when dropped into water. The SM-2 is designed to be carried aboard all vessels, as well as artificial islands and fixed structures. It is to be used as part of the required survival equipment complement. The light is used to mark a position in the water, particularly in a crew-o

Many of our products are required to be tested and approved by regulatory bodies worldwide. We believe in going beyond those specifications to insure our products work when needed in real world conditions. With proper care and maintenance your ACR product will last for years. It is important that you thoroughly read this product support manual to understand the proper care and use of your ACR product. ACR is proud to be certified to ISO 9001: 2000, the International Standard for Quality. Test li

Avoid mounting locations that subject the bracket to breaking waves. Avoid mounting locations that do not provide protection from harmful UV rays of the sun. The bracket must be mounted facing inboard to avoid being lost overboard due to impacts of breaking waves, personnel or loose gear. Visually inspect the area surrounding the mounting bracket installation site for hidden hazards or obstacles that may have been overlooked during the location selection. If there is any doubt as to the ready ac

Turning off the beacon If your beacon was manually activated and you wish to deactivate, return the thumb switch to the “OFF” position. If automatically activated and you wish to deactivate, remove the beacon from the water and dry the unit or place the beacon back into the release bracket. The beacon normally takes up to 12 seconds to deactivate. If deactivation should fail, remove the four screws holding the unit together and unplug the battery to disable the unit. Return the beacon to ACR Ele

If someone attempts to register a PLB reported as stolen, NOAA or your national authority will notify the appropriate police department. APPENDIX A - ACCESSORIES 1. Multi-Function Belt Clip The SARLink™ comes standard with a multi- function belt clip. To install the clip, simply align the bottom tabs on the clip with the insert holes located on the bottom of the beacon. Snap the clip in place by pressing the top of the clip so that the two top tabs engage in the two insert holes on the top of th

The 121.5 MHz signal is used by SAR to home in on the beacon as they approach it. The 406 MHz signal is detected by multiple satellites and from that information the location of the beacon can be calculated. This data alone is sufficient for SAR to find persons or ships in distress in a reasonable timeframe. 2. Anatomy of your beacon NOTE: When unpacking your beacon, it is recommended that you save the original packaging for re-use when shipping the beacon for battery replacement in the future.

A OWNER VESSEL RADIO CALL SIGN UIN # CAUTION: Before proceeding to install, test or use your new ACR Electronics’ product, please read this Product Support Manual in its entirety. If you have questions regarding the contents of the manual, please contact our Technical Service Department at ACR Electronics, Inc., Telephone +1 (954) 981- 3333. Please be ready to provide the technician with the page number you wish to discuss. If you have a question that is not covered in the manual, please visit o

Figure 5 - Belt Clip . 5.1 Multi-Function Belt Clip The MicrOFix™ comes standard with a multi-function belt clip. To install the clip, simply align the bottom tabs on the clip with the insert holes located on the bottom of the beacon. Snap the clip in place by pressing the top of the clip so that the two top tabs engage in the two insert holes on the top of the beacon (see figure 5). To remove the clip, push up and back on the top tabs one at a time to disengage the clip from the beacon. The Mic