The tool should be stored in a clean and dry environment. Recommended lubricants: Use John Deere AT-4003 air tool oil or any other high grade turbine oil containing moisture absorbent, rust inhibitors, metal wetting agents and an EP (extreme pressure) additive. 3/8-Inch Power Ratchet Wrench Operator's Manual Troubleshooting Troubleshooting Loss of Power 1. Low air pressure 2. Improper lubrication or dirt build up 3. Worn motor parts, or other problems 1. Check air supply. For rated performance,

Pressure Backhoe........................................................... Loader............................................................. Flow @ 2,200 rpm.................................................. Backhoe........................................................... Loader............................................................. SAE Operating Weights open center 3,625 psi (25 000 kPa) 2,900 psi (20 000 kPa) 28 gpm (106 L/min.) 28 gpm (106 L/min.) 28 gpm (106 L/min.) open center

(– 25 mm) N Width over track.........................................................................90 in. (2286 mm) 92 in. (2338 mm) 108 in. (2743 mm) O Cast reach With 20-in. (510 mm) shoes.......................................................16 in. (401 mm) With 22-in. (560 mm) shoes ..............................................................................................................15 in. (375 mm) With 30-in. (760 mm) shoes .........................................................

Stronger and faster than before, this 20-metric-ton excavator is loaded with enhancements that not only increase productivity and uptime, but lower daily operating costs, too. A high-effi ciency “on-demand” cooling system, Tier 3 PowerTech™ E diesel engine, advanced multifunction monitor, and more spacious cab with 47- percent more tinted glass headline the long list of advances. Delivering the power, smoothness, and control you expect from a John Deere, the 200D and 200D LC come with everything

3. Adjust the engine to a low speed until you see water exiting the water outlet. NOTE: This may take up to 3-5 minutes. Adjust the engine throttle back to full RPM. 4. Once the unit is primed, stop the engine and connect the high pressure discharge hose to the water outlet of the unit. NOTE: The trigger gun and dual lance assembly should already be connected to the high pressure discharge hose at this time. START-UP/COLD WATER OPERATION: 1. Refer to the "Safety Precautions" pgs. 4-7 before star

Gal. / Liters) 5 / 18.9 9 / 34 13.5 / 51 Fuel Consumption (Gal. Per Hr / Liters Per Hr) .52 / 1.97 .85 / 3.00 1.2 / 4.54 Pump Pressure (psi) 4.7 5.1 5.6 Electric Requirements 120V / 60 HZ 120V / 60 HZ 120V / 60 HZ Amperage (Normal Run) 2.8 3.6 3.6 Motor RPM 3440 3400 3400 Hot Air Output (CFM) 360 490 575 Motor HP 1/8 1/5 1/5 Shipping Weight (Approximate Pounds / Kilograms) 36 / 16.3 56 / 25.4 71 / 32.2 Space heater Weight without Fuel (Approximate Pounds / Kilograms) 32 / 14.5 48 / 21.8 61 / 27.

Wash filter assembly in clean fuel and inspect for damage. Note: It is not necessary to remove filter from filter assembly on Model T70. On Model T115 and T165 assembly is one piece. 5. Install filter assembly and bushing (Model T70) into fuel tank. IMPORTANT: Be sure filter (Model T115 and T165) and bushing (Model T70) are firmly seated in tank. 6. Connect fuel line and install side cover. Model T70 B C A Model T115 and T165 C A B 107351-01 19 Periodic Service STORAGE LOCATION AND MAINTENANCE N

Therefore, either the symbol “ ” or the words and “Double insulation” appear on the power tool or on the nameplate. Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments. To keep the double insulation system effective, follow these precautions: a. Only JOHN DEERE AUTHORIZED DEALER should disassemble or assemble this power tool, and only genuine JOHN DE

(4.27 m) Optional soundproofed cab w/integral ROPS/ FOPS Vandal protection w/built-in locks ADD VERSATILITY WITH: Mechanical front-wheel drive with: Offset driveshaft for better ground clearance Extendable dipperstick Self-adjusting hydraulic wet-disk brakes Inboard planetary final drives Transaxle 1st and 2nd collar shift, 3rd and 4th synchronized Full-power-shift reverser Torque converter Single-lever loader control Two-lever backhoe control Two-lever stabilizer control with anti-

ALWAYS PROVIDE A COPY OF THIS MANUAL TO ANYONE USING THIS EQUIPMENT. READ ALL INSTRUCTIONS IN THIS MANUAL AND ANY INSTRUCTIONS SUPPLIED BY MANUFACTURERS OF SUPPORTING EQUIPMENT BEFORE OPERATING THIS AIR COMPRESSOR AND ESPECIALLY POINT OUT THE "SAFETY WARNINGS" TO PREVENT THE POSSIBILITY OF PERSONAL INJURY TO THE OPERATOR. Once the unit has been uncrated, immediately write in the serial number of your unit in the space provided below. SERIAL NUMBER_________________________________ Inspect for sig