Remove all debris and hard or sharp objects such as glass, wire, etc. • Be aware of the risk of injury to the head, hands and feet. • Clear the area of children, bystanders, and pets. At a minimum, keep all children, bystanders, and pets outside a 50 feet (15 m.) radius; there still may be a risk to bystanders from thrown objects. Bystanders should be encouraged to wear eye protection. If you are approached, stop the unit immediately. • Squeeze the throttle control and check that it returns auto

Comply with times listed in local ordinances. Usual recommendations are 9:00 am to 5:00 pm, Monday through Saturday. • To reduce noise levels, limit the number of pieces of equipment used at any one time. • To reduce noise levels, operate power blowers at the lowest possible speed to do the job. • Check your equipment before operation, especially the muffler, air intakes and air filters. • Use rakes and brooms to loosen debris before blowing. • In dusty conditions, slightly dampen surfaces or us

Press STOP switch down to stop engine Figure 5-4A. NOTE: For emergency stopping, simply activate CHAIN BRAKE® and move STOP switch down. INERTIA CHAIN BRAKE® ACTION : NOTE: THIS SAW IS EQUIPPED WITH AN INERTIA CHAIN BRAKE.IF THE SAW KICKS BACK WHILE IN USE, THE INERTIA OF THE MOVING SAW WILL ACTIVATE THE BRAKE. A BRAKE BAND AROUND THE CLUTCH DRUM ACTIVATES AND STOPS THE MOVING CHAIN. 5-5.CHAIN BRAKE® OPERATIONAL TEST Test the CHAIN BRAKE® periodically to ensure proper function. Perform a CHAIN B

12 STARTING/STOPPING INSTRUCTIONS Fig. 16 Starting Position Operate this unit only in a well- ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 17). To avoid serious injury, the operator and unit must be in a stable position while starting. WARNING: Starter Rope Throttle Control (Squeezed) STOPPING INSTRUCTIONS 1. Release your hand from the thr

PRINTED IN U.S.A. PART NO. 769-00556 (1/03) TABLE OF CONTENTS Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Assembly Instructions . . . . . . . . . . .

P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. Chipper - Shredders Model Series 462 thru 465 Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State

PRINTED IN U.S.A. PART NO. 769-00872A (11/03) INTRODUCTION THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator’s manual provides you with easy-tounderstand operating instructions. Read the whole manual and follow all the instructions to keep your new outdoor power tool in top operating condition. PRODUCT REFERENCES, ILLUSTRATIONSAND SPECIFICATIONS All infor

Using improperly mixed fuel can severely damage the engine. Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded gasoline in a separate fuel can. Use a 40:1 fuel/oil ratio. Do not mix them directly in the engine fuel tank. See the table below for specific gas and oil mixing ratios. NOTE: One gallon (3.8 liters) of unleaded gasoline mixed with one 3.2 oz. (95 ml.) bottle of 2-cycle oil makes a 40:1 fuel/oil ratio. + UNLEADED GAS 2 CYCLE OIL 1 GALLON US 3.2 FL. OZ. (3.8 LITERS) (95

B. Keep the left arm as straight as possible. C. Keep weight on both feet. CAUTION While the saw is cutting, be sure the chain and bar are being properly lubricated. 6-4A B A C 6-3A 13 7 - MAINTENANCE INSTRUCTIONS 7 - MAINTENANCE INSTRUCTIONS All chain saw service, other than items listed here in your user manual maintenance instructions, should be performed by your nearest Authorized Service Center. 7-1.PREVENTIVE MAINTENANCE A good preventive maintenance program of regular inspection and care

If this Shredder is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. WARRANTY SERVICE IS AVAILABLE BY RETURNING THIS SHREDDER TO THE NEAREST MTD REPAIR DEALER. This warraanty gives you specific legal rights, and you may also have other rights which vary from state to state. 1 RULES FOR SAFE OPERATION RULES FOR SAFE OPERATION SYMBOL MEANING The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, a