Note While loading the tape, the drive will enter a false Ready Mode condition for a short period. During this false state the Tape In Use LED will continue to blink. Do not attempt any operations while the LED is blinking. When tape is unloaded. 5-8 Operation and Maintenance Table 5-4 Drive Operation LCD Messages When tape is loaded. DLTtype = DLTTM4000 (4000DLT), or DLTTM7000 (7000DLT). Compressed if compression mode enabled or Standard if compression mode disabled. 20/40GB = DLTTM4000, 35/70G

aci_getvolsertodrive 4-69 21 Dec 2001 Figure 4-58 Example of the aci_getvolertodrive Function /* Display volumes reserved for a drive*/ int rc, i, num; char *Drive = "Drive1"; struct aci_voltodrive_entry *drive_inf[ACI_MAX_RANGES]; rc = aci_getvolsertodrive( Drive, num, drive_inf); if( rc ) { aci_perror( "Command failed: " ); } else for (i = 0; i < ACI_MAX_RANGES; i++) { if ( *drive_inf[i]->volser == '\0' ) break; printf( "drive:%s Volser Range%d\n", drive_inf[i]->Drive, drive_inf[i]->VolserRang

Power Button 4. Install data cartridges in slots 1 through 5 of your FastStor. LCD indicates 1-5 are loaded. Quick Start Guide 5. Using the Mode Menu, move the cartridge from slot 1 to slot 6, and from slot 2 to slot 7. Press MODE button until LOAD SLOT is displayed. Press SELECT button twice. Tape in slot 1 will move to slot 6. Repeat above steps to move tape in slot 2 to slot 7. 6. Install additional data cartridges in slots 1 and 2. LCD indicates 1-7 loaded. Quick Start Guide 7. Connect SCSI

All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without prior written consent of ADIC. ADIC shall not be liable for errors contained herein or for incidental or consequential damages (including lost profits) in connection with the furnishing, performance or use of this material whether based on warranty, contract, or other legal theory. All trademarks within this document are the property of their respective owners. Copyright No

For more information, see the ADIC Management Console User Guide. The ADIC Management Console service port supports Zmodem file transfers. The procedures below are specific for using the HyperTerminal program on the service terminal to transfer files. Other terminal emulation programs operate in a similar fashion. The Zmodem send and receive functions in some terminal emulation programs automatically issue the command string “rz” before sending a file and the command string “sz” before receiving

4 Diagnostic Menu ...................................................................................................................................................................................................... 6 Barcode Function.........................................................................................................................................................................6 Barcode Labels ...............................................................................

Environmental Considerations For best performance of your Scalar Library, and to minimize the chance of condensation, please observe the following guidelines: . Install your Scalar Library on a level floor. . If you expose cartridges to temperatures outside the operating limits – 40-113°F (5-40°C) – stabilize them by leaving the cartridges in the operating temperature for a minimum of two hours before you use them. . Avoid temperature problems by ensuring that the Scalar Library rear panel is no

The barcode becomes part of the information stored in the application software. Contents Page Topic 1 What’s in the Box? 1 Tools Required 2 Installing a Barcode Reader 5 Removing a Barcode Reader 6 Contacting ADIC What’s in the Box? The following items are included in your barcode reader kit. Description Quantity Barcode reader 1 Barcode label sheet 1 Tools Required The following tools are required to work with the barcode reader kit. Description Quantity A small flat blade screw

All other trademarks are property of their respective owners. Document number: 62-0162-01 Rev A First published: March 1999 Printed in the USA Contents Introduction Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 Organization . . . . . . . . . . . . . . . . . . . . . . . . . . .

DAS is a trademark of Grau, an ADIC subsidiary. All other product names and identifications are trademarks or registered trademarks of their respective manufacturers. Copyright Notice Copyright © 1996-2000 by ADIC. All rights reserved. This document is the property of ADIC. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language in any form or by any means, electronic, mechanical, magnetic, optical,