• Battery powered push button -No wires to run. • 128selectablecodesallowmorethanonechime system in the same house. © 2007 598-1077-02 Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 1. Install alkaline type A2

Your Heath®/Zenith Chime Extender allows you to add doorbell coverage to any room in your house without the need to run additional wires.The Chime Extender "listens" for your existing doorbell to ring, then transmits a radio frequency signal to the plug-in chme unit in another part of the house. 1. Set the chime volume on the back of the plug-in chime, if desired. 2. Plug-in the doorbell chime. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than t

• Automatically turns light off. • Dusk Accent lighting. • Photocell keeps the light off during daylight hours. This package includes: • Lantern • Easy to use universal mounting bracket (X-Bar) • Mounting hardware • Wire nuts Requirements • The Light Control requires 120 volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time Works: Day Night Test 5 Seconds x x Auto 1, 5, or 10 M

Be careful when opening.DOnOtover extend the front door when opening or damage to hinges may occur. Pull From Here to Open CHiME installatiOn IMPORTANT: Proper installation requires a diode on the front door push button. See Diode Installation Instructions (page 5) after completing steps 1 through 10 below. Note: Electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualified electrician. 1. Verify transformer power rating. Power must be supplied

The chime cover style will determine orientation. 7. A cover pin is installed on two sides of the chime base. After determining correct orientation, remove, turn over, and reinstall the cover pin located on top of chime base (see Figure 1). Illustrations may vary from actual chime unit. Figure 1 - Electronic Chime Identification (2300 Base Shown) Cover Pin Volume Control Base Orientation Marking Wire Entrance Hole Front Door Tune Selection Switch (3 Selections or 10 Selections – Depending on Mod

Complete The Installation 1. Put the Temporary Pin through the holes in the Mounting Bracket. 2. This fixture must be grounded. Connect the supply ground wire to the green ground screw.You can also attach a bare or green “pigtail” to the green ground screw, then connect the ground pigtail to the supply ground when the other supply wires are connected. 3. Slide the fixture onto the Mounting Bracket, and allow the fixture to rest on the Temporary Pin. 4. Connect the fixture wires to the supply wir

(Volume control feature is available on selected chimes). 2.Testrange.Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. WirelessPlug-InChimeAccessoryReceiverModel3106978(AC-6196) This package includes (Style of chime may vary from illustration): • Wireless chime • Hardware pack Chime Volume Control (Depending upon model) Access Door 3.Setchimevolume.Locate control on back of plug-in chime. (Volume control feature is available on select

Contact a qualified electrician if there is any question as to the suitability of the system. CAUTION: Make sure the power is off before starting the installation. This fixture can be mounted on a wall with, or without using a flush-mounted junction box. Do not attempt to mount this fixture on a surface-mounted “Wet Location” junction box. Use the instructions below that apply to your application. Installation Using A Junction Box Note: If your junction box protrudes out of the wall slightly, yo

Sound travels farthest with the fewest obstacles. Do not place over heat source; i.e., radiator, heater, or stove. At the chosen location drill two small pilot holes 3 1/4" apart in the vertical plane. The chime cover is a push fit onto the base. Remove chime cover to expose base. Position base and mount in place using screws supplied, key-hole shaped slot at the 1 32 Base Plate Chime Cover top (see Figure 1). Figure 1 WIRING THE CHIME To Push Button A. Battery Operation. Do not use with lighted

1. Verify transformer power rating. Power must be supplied from a 16 Volt AC, 10 Watt or a 16 Volt AC, 15 Watt transformer (Heath®/Zenith models 122C, 121AC, or 125C). 2. Remove cover from existing chime. 3. Label all wires before disconnecting. Using masking tape, mark each wire according to existing chime terminal markings. • “F” – Front Push Button Wire • “T” – Transformer Wire • “R” – Rear Push Button Wire* 4. Disconnect all wires from existing chime. 5. Remove existing chime base from wall.